MC9S12P32CFT Freescale Semiconductor, MC9S12P32CFT Datasheet - Page 182

• Manufacturer Part Number: MC9S12P32CFT
• Description: MCU 16BIT 32K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12P32CFT

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: S12P
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, DEMO9S12PFAME
• Package: 48QFN EP
• Family Name: HCS12
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Interface Type: CAN/SCI/SPI
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

S12S Debug Module (S12SDBGV2)
6.4.5.2.1
In Normal Mode, change of flow (COF) program counter (PC) addresses are stored.
COF addresses are defined as follows:
LBRA, BRA, BSR, BGND as well as non-indexed JMP, JSR, and CALL instructions are not classified as
change of flow and are not stored in the trace buffer.
Stored information includes the full 18-bit address bus and information bits, which contains a
source/destination bit to indicate whether the stored address was a source address or destination address.
MARK1
MARK2
SUB_1
ADDR1
IRQ_ISR LDAB
MARK1
IRQ_ISR LDAB
SUB_1
ADDR1
182
•
•
•
•
Source address of taken conditional branches (long, short, bit-conditional, and loop primitives)
Destination address of indexed JMP, JSR, and CALL instruction
Destination address of RTI, RTS, and RTC instructions
Vector address of interrupts, except for BDM vectors
LDX
JMP
NOP
BRN
NOP
DBNE
STAB
RTI
LDX
JMP
STAB
RTI
BRN
NOP
DBNE
Normal Mode
When a COF instruction with destination address is executed, the
destination address is stored to the trace buffer on instruction completion,
indicating the COF has taken place. If an interrupt occurs simultaneously
then the next instruction carried out is actually from the interrupt service
routine. The instruction at the destination address of the original program
flow gets executed after the interrupt service routine.
In the following example an IRQ interrupt occurs during execution of the
indexed JMP at address MARK1. The BRN at the destination (SUB_1) is
not executed until after the IRQ service routine but the destination address
is entered into the trace buffer to indicate that the indexed JMP COF has
taken place.
The execution flow taking into account the IRQ is as follows
#SUB_1
0,X
*
A,PART5
#$F0
VAR_C1
#SUB_1
0,X
#$F0
VAR_C1
*
A,PART5
S12P-Family Reference Manual, Rev. 1.13
; IRQ interrupt occurs during execution of this
;
; JMP Destination address TRACE BUFFER ENTRY 1
; RTI Destination address TRACE BUFFER ENTRY 3
;
; Source address TRACE BUFFER ENTRY 4
; IRQ Vector $FFF2 = TRACE BUFFER ENTRY 2
;
;
;
;
;
;
NOTE
Freescale Semiconductor