MC9S12P32CFT Freescale Semiconductor, MC9S12P32CFT Datasheet - Page 421

• Manufacturer Part Number: MC9S12P32CFT
• Description: MCU 16BIT 32K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12P32CFT

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: S12P
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, DEMO9S12PFAME
• Package: 48QFN EP
• Family Name: HCS12
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Interface Type: CAN/SCI/SPI
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The direction of each serial I/O pin depends on the BIDIROE bit. If the pin is configured as an output,
serial data from the shift register is driven out on the pin. The same pin is also the serial input to the shift
register.
12.4.6
The SPI has one error condition:
12.4.6.1
If the SS input becomes low while the SPI is configured as a master, it indicates a system error where more
than one master may be trying to drive the MOSI and SCK lines simultaneously. This condition is not
permitted in normal operation, the MODF bit in the SPI status register is set automatically, provided the
MODFEN bit is set.
In the special case where the SPI is in master mode and MODFEN bit is cleared, the SS pin is not used by
the SPI. In this special case, the mode fault error function is inhibited and MODF remains cleared. In case
Freescale Semiconductor
Bidirectional Mode
•
•
•
•
When SPE = 1
Normal Mode
SPC0 = 0
SPC0 = 1
The SCK is output for the master mode and input for the slave mode.
The SS is the input or output for the master mode, and it is always the input for the slave mode.
The bidirectional mode does not affect SCK and SS functions.
Mode fault error
Error Conditions
Mode Fault Error
In bidirectional master mode, with mode fault enabled, both data pins MISO
and MOSI can be occupied by the SPI, though MOSI is normally used for
transmissions in bidirectional mode and MISO is not used by the SPI. If a
mode fault occurs, the SPI is automatically switched to slave mode. In this
case MISO becomes occupied by the SPI and MOSI is not used. This must
be considered, if the MISO pin is used for another purpose.
Serial Out
Serial In
Serial Out
SPI
Serial In
Table 12-11. Normal Mode and Bidirectional Mode
SPI
Master Mode MSTR = 1
S12P-Family Reference Manual, Rev. 1.13
BIDIROE
NOTE
MOMI
MOSI
MISO
Serial Out
Serial In
Serial Out
SPI
Serial In
SPI
Slave Mode MSTR = 0
Serial Peripheral Interface (S12SPIV5)
BIDIROE
SISO
MOSI
MISO
421