MC9S12P32CFT Freescale Semiconductor, MC9S12P32CFT Datasheet - Page 326

• Manufacturer Part Number: MC9S12P32CFT
• Description: MCU 16BIT 32K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12P32CFT

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: S12P
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, DEMO9S12PFAME
• Package: 48QFN EP
• Family Name: HCS12
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Interface Type: CAN/SCI/SPI
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Analog-to-Digital Converter (ADC12B10C)
be edge or level sensitive with polarity control.
combinations of control bits and their effect on the external trigger function.
During a conversion, if additional active edges are detected the overrun error flag ETORF is set.
In either level or edge triggered modes, the first conversion begins when the trigger is received.
Once ETRIGE is enabled, conversions cannot be started by a write to ATDCTL5, but rather must be
triggered externally.
If the level mode is active and the external trigger both de-asserts and re-asserts itself during a conversion
sequence, this does not constitute an overrun. Therefore, the flag is not set. If the trigger is left asserted in
level mode while a sequence is completing, another sequence will be triggered immediately.
9.4.2.2
The input channel pins can be multiplexed between analog and digital data. As analog inputs, they are
multiplexed and sampled as analog channels to the A/D converter. The analog/digital multiplex operation
is performed in the input pads. The input pad is always connected to the analog input channels of the
ADC12B10C. The input pad signal is buffered to the digital port registers. This buffer can be turned on or
off with the ATDDIEN register. This is important so that the buffer does not draw excess current when
analog potentials are presented at its input.
9.5
At reset the ADC12B10C is in a power down state. The reset state of each individual bit is listed within
the Register Description section (see
and their bit-field.
326
Resets
General-Purpose Digital Port Operation
ETRIGLE
X
X
0
0
1
1
ETRIGP
X
X
0
1
0
1
Table 9-22. External Trigger Control Bits
S12P-Family Reference Manual, Rev. 1.13
Section 9.3.2, “Register
ETRIGE
0
0
1
1
1
1
Table 9-22
SCAN
X
X
X
X
0
1
Ignores external trigger. Performs one
conversion sequence and stops.
Ignores external trigger. Performs
continuous conversion sequences.
Falling edge triggered. Performs one
conversion sequence per trigger.
Rising edge triggered. Performs one
conversion sequence per trigger.
Trigger active low. Performs continuous
conversions while trigger is active.
Trigger active high. Performs continuous
conversions while trigger is active.
gives a brief description of the different
Descriptions”) which details the registers
Description
Freescale Semiconductor