MC9S12P32CFT Freescale Semiconductor, MC9S12P32CFT Datasheet - Page 446

• Manufacturer Part Number: MC9S12P32CFT
• Description: MCU 16BIT 32K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12P32CFT

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: S12P
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, DEMO9S12PFAME
• Package: 48QFN EP
• Family Name: HCS12
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Interface Type: CAN/SCI/SPI
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

128 KByte Flash Module (S12FTMRC128K1V1)
13.3.2.11.1 FCCOB - NVM Command Mode
NVM command mode uses the indexed FCCOB register to provide a command code and its relevant
parameters to the Memory Controller. The user first sets up all required FCCOB fields and then initiates
the command’s execution by writing a 1 to the CCIF bit in the FSTAT register (a 1 written by the user
clears the CCIF command completion flag to 0). When the user clears the CCIF bit in the FSTAT register
all FCCOB parameter fields are locked and cannot be changed by the user until the command completes
(as evidenced by the Memory Controller returning CCIF to 1). Some commands return information to the
FCCOB register array.
The generic format for the FCCOB parameter fields in NVM command mode is shown in
The return values are available for reading after the CCIF flag in the FSTAT register has been returned to
1 by the Memory Controller. Writes to the unimplemented parameter fields (CCOBIX = 110 and CCOBIX
= 111) are ignored with reads from these fields returning 0x0000.
Table 13-23
contains the command code, followed by the parameters for this specific Flash command. For details on
the FCCOB settings required by each command, see the Flash command descriptions in
446
Offset Module Base + 0x000A
Offset Module Base + 0x000B
Reset
Reset
W
W
R
R
shows the generic Flash command format. The high byte of the first word in the CCOB array
0
0
7
7
Figure 13-17. Flash Common Command Object Low Register (FCCOBLO)
Figure 13-16. Flash Common Command Object High Register (FCCOBHI)
CCOBIX[2:0]
000
001
010
Table 13-23. FCCOB - NVM Command Mode (Typical Usage)
0
0
6
6
Byte
LO
LO
LO
S12P-Family Reference Manual, Rev. 1.13
HI
HI
HI
0
0
5
5
FCCOB Parameter Fields (NVM Command Mode)
FCMD[7:0] defining Flash command
0
0
4
4
CCOB[15:8]
6’h0, Global address [17:16]
CCOB[7:0]
Global address [15:8]
Global address [7:0]
Data 0 [15:8]
Data 0 [7:0]
0
0
3
3
0
0
2
2
Freescale Semiconductor
0
0
1
1
Section
Table
13-23.
13.4.5.
0
0
0
0