MCF5272VM66 Freescale Semiconductor, MCF5272VM66 Datasheet - Page 433

• Manufacturer Part Number: MCF5272VM66
• Description: IC MPU 66MHZ COLDFIRE 196-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5272VM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART, USB
• Peripherals: DMA, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (4K x 32)
• Program Memory Type: ROM
• Ram Size: 1K x 32
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 196-MAPBGA
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Cpu Speed: 66MHz
• Embedded Interface Type: UART, QSPI, USB, TDM
• Digital Ic Case Style: BGA
• No. Of Pins: 196
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

19.6.12 SDRAM Bank Selects (SDBA[1:0])
These outputs are the SDRAM bank select signals.
19.6.13 SDRAM Row Address 10 (A10)/A10 Precharge (A10_PRECHG)
This output is the SDRAM row address 10 and the precharge strobe.
19.7
This section describes clock and reset signals in the CPU.
19.7.1
RSTI is the primary reset input to the device. Asserting RSTI immediately resets the CPU and peripherals.
However, the reset of the SDRAM controller and hence SDRAM contents depend on DRESETEN.
Asserting RSTI also causes RSTO to be asserted for 32K CPU clock cycles.
19.7.2
DRESETEN is asserted to indicate that the SDRAM controller is to be reset whenever RSTI asserts. If
DRESETEN is high, RSTI does not affect the SDRAM controller, which continues to refresh external
memory. This is useful for debug situations where a reset of the device is required without losing data
located in SDRAM. DRESETEN is normally tied high or low depending on system requirements. It should
never be tied to RSTI or RSTO.
19.7.3
CLKIN should be connected to an external clock oscillator. The CLKIN input frequency can range from
DC to 66 MHz. The frequency input to this signal must be greater than twice the frequency applied at E_Tx
CLK. The clock frequency applied to CLKIN must exceed 24 MHz when the system uses a USB
peripheral.
19.7.4
Reset output (RSTO) is driven low for 128 CPU clocks when the soft reset bit of the system configuration
register (SCR[SOFTRST]) is set. It is driven low for 32K CPU clocks when the software watchdog timer
times out or when a low input level is applied to RSTI.
19.8
The six interrupt request inputs (INT[6:1]) can generate separate, maskable interrupts on negative edge
(high to low) or positive edge (low to high) transitions. In addition to the triggering edge being
programmable, the priority can also be programmed. Each interrupt input has a separate programmable
interrupt level.
Freescale Semiconductor
CPU Clock and Reset Signals
Interrupt Request Inputs (INT[6:1])
RSTI
DRESETEN
CPU External Clock (CLKIN)
Reset Output (RSTO)
MCF5272 ColdFire
®
Integrated Microprocessor User’s Manual, Rev. 3
Signal Descriptions
19-23