MCF5272VM66 Freescale Semiconductor, MCF5272VM66 Datasheet - Page 451

• Manufacturer Part Number: MCF5272VM66
• Description: IC MPU 66MHZ COLDFIRE 196-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5272VM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART, USB
• Peripherals: DMA, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (4K x 32)
• Program Memory Type: ROM
• Ram Size: 1K x 32
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 196-MAPBGA
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Cpu Speed: 66MHz
• Embedded Interface Type: UART, QSPI, USB, TDM
• Digital Ic Case Style: BGA
• No. Of Pins: 196
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

TA must always be negated before it can be recognized as asserted again. If held asserted into the following
bus cycle, it has no effect and does not terminate the bus cycle.
TA is not used for termination during SDRAM accesses.
20.2.5
An external slave asserts this active-low input signal to abort a transfer. The assertion of TEA immediately
aborts the bus cycle. The assertion of TEA has precedence over the assertion of TA.
The MCF5272 edge-detects and retimes the TEA input. TEA is an asynchronous input signal.
The TEA signal function is available after reset. If TEA is not used, a pullup resistor or gating logic must
be used to ensure the input is inactive. TEA should be negated on the negating edge of the active chip
select. TEA must always be negated before it can be recognized as asserted again. If held asserted into the
following bus cycle, it has no effect and does not abort the bus cycle.
TEA has no affect during SDRAM accesses.
20.3
When a bus error or an address error occurs during the exception processing sequence for a previous bus
error, a previous address error, or a reset exception, the bus or address error causes a double bus fault. If
the MCF5272 experiences a double bus fault, it enters the halted state. To exit the halt state, reset the
MCF5272.
20.4
The MCF5272 uses the address bus (A[22:0]) to specify the location for a data transfer and the data bus
(D[31:0] or D[31:16]) to transfer the data. Control signals indicate the direction of the transfer. The
selected device or the number of wait states programmed in the chip select base registers (CSBRs), the
chip select option registers (CSORs), the SDRAM configuration and SDRAM timing registers (SDCR,
SDTR) control the length of the cycle.
The MCF5272 clock is distributed internally to provide logic timing. All SRAM and ROM mode bus
signals should be considered as asynchronous with respect to CLKIN. SDCR[INV] allows the SDRAM
control signals to be asserted and negated synchronous with the rising or falling edge of SDCLK. The
SDRAM control signals are BS[3:0], SDBA[1:0], RAS0, CAS0, SDWE, A10_PRECHG, SDCLKE, and
CS7/SDCS.
The asynchronous INT[6:1] signals are internally synchronized to resolve the input to a valid level before
being used.
Freescale Semiconductor
Bus Exception: Double Bus Fault
Bus Characteristics
Transfer Error Acknowledge (TEA)
For the MCF5272 to accept the transfer as successful with a transfer
acknowledge, TEA must be negated throughout the transfer.
MCF5272 ColdFire
®
Integrated Microprocessor User’s Manual, Rev. 3
NOTE
Bus Operation
20-3