SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 1005

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

39.7.15
Name:
Address:
Access:
• FRCESTALL: Stall Handshake Request Set
0 = no effect.
1 = set this bit to request a STALL answer to the host for the next handshake
Refer to chapters 8.4.5 (Handshake Packets) and 9.4.5 (Get Status) of the Universal Serial Bus Specification, Rev 2.0 for
more information on the STALL handshake.
• KILL_BANK: KILL Bank Set (for IN Endpoint)
0 = no effect.
1 = kill the last written bank.
• TX_PK_RDY: TX Packet Ready Set
0 = no effect.
1 = set this bit after a packet has been written into the endpoint FIFO for IN data transfers
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
– This flag is used to generate a Data IN transaction (device to host).
– Device firmware checks that it can write a data payload in the FIFO, checking that TX_PK_RDY is cleared.
– Transfer to the FIFO is done by writing in the “Buffer Address” register.
– Once the data payload has been transferred to the FIFO, the firmware notifies the UDPHS device setting
– UDPHS bus transactions can start.
– TXCOMP is set once the data payload has been received by the host.
– Data should be written into the endpoint FIFO only after this bit has been cleared.
– Set this bit without writing data to the endpoint FIFO to send a Zero Length Packet.
31
23
15
–
–
–
7
–
TX_PK_RDY to one.
UDPHS Endpoint Set Status Register
UDPHS_EPTSETSTAx [x=0..6]
0x400A4114 [0], 0x400A4134 [1], 0x400A4154 [2], 0x400A4174 [3], 0x400A4194 [4], 0x400A41B4 [5],
0x400A41D4 [6]
Write-only
30
22
14
–
–
–
6
–
FRCESTALL
29
21
13
–
–
–
5
28
20
12
–
–
–
4
–
TX_PK_RDY
27
19
11
–
–
3
–
26
18
10
–
–
–
2
–
KILL_BANK
SAM3U Series
SAM3U Series
25
17
–
–
9
1
–
24
16
–
–
8
–
0
–
1005
1005