SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 358

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.9
25.9.1
25.9.2
Figure 25-4.
Figure 25-5.
25.9.2.1
358
358
Connection to External Devices
SAM3U Series
SAM3U Series
Data Bus Width
Byte Write or Byte Select Access
Byte Write Access
Memory Connection for an 8-bit Data Bus
Memory Connection for a 16-bit Data Bus
A data bus width of 8 or 16 bits can be selected for each chip select. This option is controlled by
the field DBW in SMC_MODE (Mode Register) for the corresponding chip select.
Figure 25-4
connect a 512K x 16-bit memory on NCS2.
Each chip select with a 16-bit data bus can operate with one of two different types of write
access: byte write or byte select access. This is controlled by the BAT field of the SMC_MODE
register for the corresponding chip select.
Byte write access supports one byte write signal per byte of the data bus and a single read
signal.
Note that the SMC does not allow boot in Byte Write Access mode.
• For 16-bit devices: the SMC provides NWR0 and NWR1 write signals for respectively, byte0
(lower byte) and byte1 (upper byte) of a 16-bit bus. One single read signal (NRD) is provided.
Byte Write Access is used to connect 2 x 8-bit devices as a 16-bit memory.
SMC
SMC
shows how to connect a 512K x 8-bit memory on NCS2.
D[15:0]
NCS[2]
A[19:2]
NBS0
NBS1
NWE
A[18:2]
NCS[2]
NRD
D[7:0]
NWE
A1
NRD
A0
A1
D[7:0]
A[18:2]
Write Enable
Output Enable
Memory Enable
D[15:0]
A[18:1]
A[0]
Low Byte Enable
High Byte Enable
Write Enable
Output Enable
Memory Enable
A0
A1
Figure 25-5
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
shows how to