SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 730

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

35.7.8.7
35.7.9
35.7.9.1
Figure 35-40. Normal Mode Configuration
35.7.9.2
Figure 35-41. Automatic Echo Mode Configuration
730
730
WRITE BUFFER
DATA 0
DATA N
|
|
|
|
SAM3U Series
SAM3U Series
Test Modes
Receiver Timeout
Normal Mode
Automatic Echo Mode
(Peripheral) DMA
Controller
reception but only a low level. However, this low level must be present on the slave select line
(NSS) at least 1 Tbit before the first serial clock cycle corresponding to the MSB bit.
Because the receiver baudrate clock is active only during data transfers in SPI Mode, a receiver
timeout is impossible in this mode, whatever the Time-out value is (field TO) in the Time-out
Register (US_RTOR).
The USART can be programmed to operate in three different test modes. The internal loopback
capability allows on-board diagnostics. In the loopback mode the USART interface pins are dis-
connected or not and reconfigured for loopback internally or externally.
Normal mode connects the RXD pin on the receiver input and the transmitter output on the TXD
pin.
Automatic echo mode allows bit-by-bit retransmission. When a bit is received on the RXD pin, it
is sent to the TXD pin, as shown in
the TXD pin. The RXD pin is still connected to the receiver input, thus the receiver remains
active.
APB bus
TXRDY
Transmitter
Transmitter
Receiver
Receiver
LIN CONTROLLER
USART3
Figure
READ BUFFER
DATA N
DATA 0
|
|
|
|
35-41. Programming the transmitter has no effect on
RXD
TXD
RXD
TXD
(Peripheral) DMA
Controller
APB bus
RXRDY
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
NACT = SUBSCRIBE
LIN CONTROLLER
USART3