SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 1016

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

39.7.21
Name:
Address:
Access:
Note:
• CHANN_ENB (Channel Enable Command)
0 = DMA channel is disabled at and no transfer will occur upon request. This bit is also cleared by hardware when the chan-
nel source bus is disabled at end of buffer.
If the UDPHS_DMACONTROL register LDNXT_DSC bit has been cleared by descriptor loading, the firmware will have to
set the corresponding CHANN_ENB bit to start the described transfer, if needed.
If the UDPHS_DMACONTROL register LDNXT_DSC bit is cleared, the channel is frozen and the channel registers may
then be read and/or written reliably as soon as both UDPHS_DMASTATUS register CHANN_ENB and CHANN_ACT flags
read as 0.
If a channel request is currently serviced when this bit is cleared, the DMA FIFO buffer is drained until it is empty, then the
UDPHS_DMASTATUS register CHANN_ENB bit is cleared.
If the LDNXT_DSC bit is set at or after this bit clearing, then the currently loaded descriptor is skipped (no data transfer
occurs) and the next descriptor is immediately loaded.
1 = UDPHS_DMASTATUS register CHANN_ENB bit will be set, thus enabling DMA channel data transfer. Then any pend-
ing request will start the transfer. This may be used to start or resume any requested transfer.
• LDNXT_DSC: Load Next Channel Transfer Descriptor Enable (Command)
0 = no channel register is loaded after the end of the channel transfer.
1 = the channel controller loads the next descriptor after the end of the current transfer, i.e. when the
UDPHS_DMASTATUS/CHANN_ENB bit is reset.
If the UDPHS_DMA CONTROL/CHANN_ENB bit is cleared, the next descriptor is immediately loaded upon transfer
request.
1016
1016
BURST_LCK
31
23
15
–
7
Channel 0 is not used.
SAM3U Series
SAM3U Series
UDPHS DMA Channel Control Register
UDPHS_DMACONTROLx [x = 0..5]
0x400A4308 [0], 0x400A4318 [1], 0x400A4328 [2], 0x400A4338 [3], 0x400A4348 [4], 0x400A4358 [5]
Read-write
DESC_LD_IT
30
22
14
–
6
END_BUFFIT
29
21
13
–
5
END_TR_IT
28
20
12
–
4
BUFF_LENGTH
BUFF_LENGTH
END_B_EN
27
19
11
–
3
END_TR_EN
26
18
10
–
2
LDNXT_DSC
25
17
9
–
1
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
CHANN_ENB
24
16
8
–
0