SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 623

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• BITS: Bits Per Transfer
(See the
The BITS field determines the number of data bits transferred. Reserved values should not be used.
• SCBR: Serial Clock Baud Rate
In Master Mode, the SPI Interface uses a modulus counter to derive the SPCK baud rate from the Master Clock MCK. The
Baud rate is selected by writing a value from 1 to 255 in the SCBR field. The following equations determine the SPCK baud
rate:
Programming the SCBR field at 0 is forbidden. Triggering a transfer while SCBR is at 0 can lead to unpredictable results.
At reset, SCBR is 0 and the user has to program it at a valid value before performing the first transfer.
Note:
• DLYBS: Delay Before SPCK
This field defines the delay from NPCS valid to the first valid SPCK transition.
When DLYBS equals zero, the NPCS valid to SPCK transition is 1/2 the SPCK clock period.
Otherwise, the following equations determine the delay:
• DLYBCT: Delay Between Consecutive Transfers
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
Value
10
11
12
13
14
15
16
If one of the SCBR fields inSPI_CSRx is set to 1, the other SCBR fields in SPI_CSRx must be set to 1 as well, if they are
required to process transfers. If they are not used to transfer data, they can be set at any value.
0
1
2
3
4
5
6
7
8
(Note:)
below the register table;
Name
8_BIT
9_BIT
10_BIT
11_BIT
12_BIT
13_BIT
14_BIT
15_BIT
16_BIT
–
–
–
–
–
–
–
Delay Before SPCK
SPCK Baudrate
Section 32.8.9 “SPI Chip Select Register” on page
=
Description
8 bits for transfer
9 bits for transfer
10 bits for transfer
11 bits for transfer
12 bits for transfer
13 bits for transfer
14 bits for transfer
15 bits for transfer
16 bits for transfer
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
-------------- -
SCBR
MCK
=
DLYBS
------------------ -
MCK
622.)
SAM3U Series
SAM3U Series
623
623