SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 72

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

13.4.5
72
SAM3U Series
Bit-banding
Memory accesses to Strongly-ordered memory, such as the system control block, do not require
the use of DMB instructions.
A bit-band region maps each word in a bit-band alias region to a single bit in the bit-band region.
The bit-band regions occupy the lowest 1MB of the SRAM and peripheral memory regions.
The memory map has two 32MB alias regions that map to two 1MB bit-band regions:
Table 13-6.
Address
range
0x20000000-
0x200FFFFF
0x22000000-
0x23FFFFFF
• Vector table. If the program changes an entry in the vector table, and then enables the
• Self-modifying code. If a program contains self-modifying code, use an ISB instruction
• Memory map switching. If the system contains a memory map switching mechanism, use a
• Dynamic exception priority change. When an exception priority has to change when the
• Using a semaphore in multi-master system. If the system contains more than one bus
• accesses to the 32MB SRAM alias region map to the 1MB SRAM bit-band region, as shown
• accesses to the 32MB peripheral alias region map to the 1MB peripheral bit-band region, as
corresponding exception, use a DMB instruction between the operations. This ensures that if
the exception is taken immediately after being enabled the processor uses the new exception
vector.
immediately after the code modification in the program. This ensures subsequent instruction
execution uses the updated program.
DSB instruction after switching the memory map in the program. This ensures subsequent
instruction execution uses the updated memory map.
exception is pending or active, use DSB instructions after the change. This ensures the
change takes effect on completion of the DSB instruction.
master, for example, if another processor is present in the system, each processor must use
a DMB instruction after any semaphore instructions, to ensure other bus masters see the
memory transactions in the order in which they were executed.
in
shown in
Table 13-6
– Use an ISB instruction to ensure the new MPU setting takes effect immediately after
programming the MPU region or regions, if the MPU configuration code was
accessed using a branch or call. If the MPU configuration code is entered using
exception mechanisms, then an ISB instruction is not required.
Table
SRAM memory bit-banding regions
Memory
region
SRAM bit-band
region
SRAM bit-band alias
13-7.
Instruction and data accesses
Direct accesses to this memory range behave as SRAM
memory accesses, but this region is also bit addressable
through bit-band alias.
Data accesses to this region are remapped to bit band
region. A write operation is performed as read-modify-write.
Instruction accesses are not remapped.
6430E–ATARM–29-Aug-11