SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 836

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

37.11.1
37.11.2
37.12 HSMCI Transfer Done Timings
37.12.1
37.12.2
836
836
SAM3U Series
SAM3U Series
Boot Procedure, Processor Mode
Boot Procedure DMA Mode
Definition
Read Access
The XFRDONE flag in the HSMCI_SR indicates exactly when the read or write sequence is
finished.
During a read access, the XFRDONE flag behaves as shown in
1. Configure the HSMCI data bus width programming SDCBUS Field in the
2. Set the byte count to 512 bytes and the block count to the desired number of blocks,
3. Issue the Boot Operation Request command by writing to the HSMCI_CMDR register
4. The BOOT_ACK field located in the HSMCI_CMDR register must be set to one, if the
5. Host processor can copy boot data sequentially as soon as the RXRDY flag is
6. When Data transfer is completed, host processor shall terminate the boot stream by
1. Configure the HSMCI data bus width by programming SDCBUS Field in the
2. Set the byte count to 512 bytes and the block count to the desired number of blocks by
3. Enable DMA transfer in the HSMCI_DMA register.
4. Configure DMA controller, program the total amount of data to be transferred and
5. Issue the Boot Operation Request command by writing to the HSMCI_CMDR register
6. DMA controller copies the boot partition to the memory.
7. When DMA transfer is completed, host processor shall terminate the boot stream by
HSMCI_SDCR register. The BOOT_BUS_WIDTH field located in the device Extended
CSD register must be set accordingly.
writing BLKLEN and BCNT fields of the HSMCI_BLKR Register.
with SPCMD field set to BOOTREQ, TRDIR set to READ and TRCMD set to “start data
transfer”.
BOOT_ACK field of the MMC device located in the Extended CSD register is set to one.
asserted.
writing the HSMCI_CMDR register with SPCMD field set to BOOTEND.
HSMCI_SDCR register. The BOOT_BUS_WIDTH field in the device Extended CSD
register must be set accordingly.
writing BLKLEN and BCNT fields of the HSMCI_BLKR Register.
enable the relevant channel.
with SPCND set to BOOTREQ, TRDIR set to READ and TRCMD set to “start data
transfer”.
writing the HSMCI_CMDR register with SPCMD field set to BOOTEND.
Figure
37-11.
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11