SAM3U1C Atmel Corporation, SAM3U1C Datasheet - Page 363

• Manufacturer Part Number: SAM3U1C
• Manufacturer: Atmel Corporation

Specifications of SAM3U1C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.10.3
25.10.3.1
25.10.3.2
Figure 25-10. Write Cycle
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
Write Waveforms
NWE Waveforms
NCS Waveforms
NBS0, NBS1,
A0, A1
A [23:2]
NWE
MCK
NCS
The write protocol is similar to the read protocol. It is depicted in
starts with the address setting on the memory address bus.
The NWE signal is characterized by a setup timing, a pulse width and a hold timing.
The NWE waveforms apply to all byte-write lines in Byte Write access mode: NWR0 to NWR3.
The NCS signal waveforms in write operation are not the same as those applied in read opera-
tions, but are separately defined:
1. NWE_SETUP: the NWE setup time is defined as the setup of address and data before
2. NWE_PULSE: The NWE pulse length is the time between NWE falling edge and NWE
3. NWE_HOLD: The NWE hold time is defined as the hold time of address and data after
1. NCS_WR_SETUP: the NCS setup time is defined as the setup time of address before
2. NCS_WR_PULSE: the NCS pulse length is the time between NCS falling edge and
3. NCS_WR_HOLD: the NCS hold time is defined as the hold time of address after the
NCS_WR_SETUP
the NWE falling edge.
rising edge.
the NWE rising edge.
the NCS falling edge.
NCS rising edge.
NCS rising edge.
NWE_SETUP
NCS_WR_PULSE
NWE_CYCLE
NWE_PULSE
NWE_HOLD
NCS_WR_HOLD
Figure
SAM3U Series
SAM3U Series
25-10. The write cycle
363
363