MC9S12HZ128VAL Freescale Semiconductor, MC9S12HZ128VAL Datasheet - Page 39

• Manufacturer Part Number: MC9S12HZ128VAL
• Description: IC MCU 16BIT 2K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12HZ128VAL

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, I²C, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 112-LQFP
• Processor Series: S12H
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 6 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1.5.6.3
PB7–PB0 are general-purpose input or output pins. They can be configured as frontplane segment driver
outputs FP7–FP0 of the LCD. In MCU expanded modes of operation, these pins are used for the
multiplexed external address and data bus.
1.5.6.4
PE7 is a general-purpose input or output pin. It can be configured as frontplane segment driver output FP22
of the LCD module.
The XCLKS is an input signal which controls whether a crystal in combination with the internal Colpitts
(low power) oscillator is used or whether Pierce oscillator/external clock circuitry is used. The state of this
pin is latched at the rising edge of RESET. If the input is a logic high the EXTAL pin is configured for an
external clock drive or a Pierce Oscillator. If the input is a logic low a Colpitts oscillator circuit is
configured on EXTAL and XTAL. Because this pin is an input with a pull-down device during reset, if the
pin remains floating, the default configuration is a Colpitts oscillator circuit on EXTAL and XTAL.
Freescale Semiconductor
PB[7:0] / FP[7:0] / ADDR[7:0] / DATA[7:0] — Port B I/O Pins
PE7 / FP22 / XCLKS / NOACC — Port E I/O Pin 7
* Rs can be zero (shorted) when use with higher frequency crystals.
Refer to manufacturer’s data.
* Due to the nature of a translated ground Colpitts oscillator a
DC voltage bias is applied to the crystal. Please contact
the crystal manufacturer for crystal DC.
MCU
MCU
Figure 1-10. Colpitts Oscillator Connections (PE7 = 0)
EXTAL
Figure 1-11. Pierce Oscillator Connections (PE7 = 1)
XTAL
EXTAL
XTAL
MC9S12HZ256 Data Sheet, Rev. 2.05
R
S
*
R
CDC*
B
C1
C2
ceramic resonator
Crystal or
C
C
V
2
1
SSPLL
ceramic resonator
V
Chapter 1 MC9S12HZ256 Device Overview
Crystal or
SSPLL
39