MC9S12HZ128VAL Freescale Semiconductor, MC9S12HZ128VAL Datasheet - Page 73

• Manufacturer Part Number: MC9S12HZ128VAL
• Description: IC MCU 16BIT 2K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12HZ128VAL

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, I²C, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 112-LQFP
• Processor Series: S12H
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 6 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.3.2.8
The banked FCMD register is the Flash command register.
Freescale Semiconductor
ACCERR
BLANK
CBEIF
PVIOL
Field
CCIF
FAIL
7
6
5
4
2
1
Command Buffer Empty Interrupt Flag — The CBEIF flag indicates that the address, data and command
buffers are empty so that a new command write sequence can be started. The CBEIF flag is cleared by writing
a 1 to CBEIF. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned
word to the Flash address space but before CBEIF is cleared will abort a command write sequence and cause
the ACCERR flag to be set. Writing a 0 to CBEIF outside of a command write sequence will not set the ACCERR
flag. The CBEIF flag is used together with the CBEIE bit in the FCNFG register to generate an interrupt request
(see
0 Buffers are full.
1 Buffers are ready to accept a new command.
Command Complete Interrupt Flag — The CCIF flag indicates that there are no more commands pending. The
CCIF flag is cleared when CBEIF is clear and sets automatically upon completion of all active and pending
commands. The CCIF flag does not set when an active commands completes and a pending command is
fetched from the command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together
with the CCIE bit in the FCNFG register to generate an interrupt request (see
0 Command in progress.
1 All commands are completed.
Protection Violation Flag — The PVIOL flag indicates an attempt was made to program or erase an address
in a protected area of the Flash block during a command write sequence. The PVIOL flag is cleared by writing a
1 to PVIOL. Writing a 0 to the PVIOL flag has no effect on PVIOL. While PVIOL is set, it is not possible to launch
a command or start a command write sequence.
0 No failure.
1 A protection violation has occurred.
Access Error Flag — The ACCERR flag indicates an illegal access to the Flash array caused by either a
violation of the command write sequence, issuing an illegal command (illegal combination of the CMDBx bits in
the FCMD register), launching the sector erase abort command terminating a sector erase operation early or the
execution of a CPU STOP instruction while a command is executing (CCIF = 0). The ACCERR flag is cleared by
writing a 1 to ACCERR. Writing a 0 to the ACCERR flag has no effect on ACCERR. While ACCERR is set in any
of the banked FTSAT registers, it is not possible to launch a command or start a command write sequence in any
of the Flash blocks. If ACCERR is set by an erase verify operation or a data compress operation, any buffered
command will not launch.
0 No access error detected.
1 Access error has occurred.
Erase Verify Operation Status Flag — When the CCIF flag is set after completion of an erase verify command,
the BLANK flag indicates the result of the erase verify operation. The BLANK flag is cleared by the Flash module
when CBEIF is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect
on BLANK.
0 Flash block verified as not erased.
1 Flash block verified as erased.
Flag Indicating a Failed Flash Operation — The FAIL flag will set if the erase verify operation fails (selected
Flash block verified as not erased). The FAIL flag is cleared by writing a 1 to FAIL. Writing a 0 to the FAIL flag
has no effect on FAIL.
0 Flash operation completed without error.
1 Flash operation failed.
Flash Command Register (FCMD)
Figure
2-29)
.
Table 2-16. FSTAT Field Descriptions
MC9S12HZ256 Data Sheet, Rev. 2.05
Description
Chapter 2 256 Kbyte Flash Module (FTS256K2V1)
Figure
2-29).
73