MC9S12HZ128VAL Freescale Semiconductor, MC9S12HZ128VAL Datasheet - Page 417

• Manufacturer Part Number: MC9S12HZ128VAL
• Description: IC MCU 16BIT 2K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12HZ128VAL

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, I²C, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 112-LQFP
• Processor Series: S12H
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 6 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.5.1
The SCI only originates interrupt requests. The following is a description of how the SCI makes a request
and how the MCU should acknowledge that request. The interrupt vector offset and interrupt number are
chip dependent. The SCI only has a single interrupt line (SCI interrupt signal, active high operation) and
all the following interrupts, when generated, are ORed together and issued through that port.
13.5.1.1
The TDRE interrupt is set high by the SCI when the transmit shift register receives a byte from the SCI
data register. A TDRE interrupt indicates that the transmit data register (SCIDRH/L) is empty and that a
new byte can be written to the SCIDRH/L for transmission.Clear TDRE by reading SCI status register 1
with TDRE set and then writing to SCI data register low (SCIDRL).
13.5.1.2
The TC interrupt is set by the SCI when a transmission has been completed.A TC interrupt indicates that
there is no transmission in progress. TC is set high when the TDRE flag is set and no data, preamble, or
break character is being transmitted. When TC is set, the TXD pin becomes idle (logic 1). Clear TC by
reading SCI status register 1 (SCISR1) with TC set and then writing to SCI data register low (SCIDRL).TC
is cleared automatically when data, preamble, or break is queued and ready to be sent.
13.5.1.3
The RDRF interrupt is set when the data in the receive shift register transfers to the SCI data register. A
RDRF interrupt indicates that the received data has been transferred to the SCI data register and that the
byte can now be read by the MCU. The RDRF interrupt is cleared by reading the SCI status register one
(SCISR1) and then reading SCI data register low (SCIDRL).
13.5.1.4
The OR interrupt is set when software fails to read the SCI data register before the receive shift register
receives the next frame. The newly acquired data in the shift register will be lost in this case, but the data
already in the SCI data registers is not affected. The OR interrupt is cleared by reading the SCI status
register one (SCISR1) and then reading SCI data register low (SCIDRL).
13.5.1.5
The IDLE interrupt is set when 10 consecutive logic 1s (if M = 0) or 11 consecutive logic 1s (if M = 1)
appear on the receiver input. After the IDLE is cleared, a valid frame must again set the RDRF flag before
an idle condition can set the IDLE flag. Clear IDLE by reading SCI status register 1 (SCISR1) with IDLE
set and then reading SCI data register low (SCIDRL).
Freescale Semiconductor
Description of Interrupt Operation
TDRE Description
TC Description
RDRF Description
OR Description
IDLE Description
IDLE
SCISR1[4]
Table 13-17. SCI Interrupt Sources
MC9S12HZ256 Data Sheet, Rev. 2.05
ILIE
Active high level. Indicates that receiver input
has become idle.
Chapter 13 Serial Communication Interface (SCIV4)
417