S912XET512J3VALR Freescale Semiconductor, S912XET512J3VALR Datasheet - Page 339

• Manufacturer Part Number: S912XET512J3VALR
• Description: 16-bit Microcontrollers - MCU 16 BIT,512K FLASH
• Manufacturer: Freescale Semiconductor

Specifications of S912XET512J3VALR

• Rohs: yes
• Core: HCS12X
• Processor Series: MC9S12XE
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 512 KB
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3.13 V to 5.5 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: LQFP-112
• Mounting Style: SMD/SMT

CPU12X Information Byte
CXINF Information Byte
This describes the format of the information byte used only when tracing in Detail Mode. When tracing
from the CPU12X in Detail Mode, information is stored to the trace buffer on all cycles except opcode
fetch and free cycles. The XGATE entry stored on the same line is a snapshot of the XGATE program
counter. In this case the CSZ and CRW bits indicate the type of access being made by the CPU12X, whilst
the XACK and XOCF bits indicate if the simultaneous XGATE cycle is a free cycle (no bus acknowledge)
or opcode fetch cycle. Similarly when tracing from the XGATE in Detail Mode, information is stored to
the trace buffer on all cycles except opcode fetch and free cycles. The CPU12X entry stored on the same
line is a snapshot of the CPU12X program counter. In this case the XSZ and XRW bits indicate the type
of access being made by the XGATE, whilst the CFREE and COCF bits indicate if the simultaneous
CPU12X cycle is a free cycle or opcode fetch cycle.
Freescale Semiconductor
CFREE
Field
Field
CSD
CVA
CDV
7
6
4
7
Source Destination Indicator — This bit indicates if the corresponding stored address is a source or destination
address. This is only used in Normal and Loop1 mode tracing.
0 Source address
1 Destination address
Vector Indicator — This bit indicates if the corresponding stored address is a vector address. Vector addresses
are destination addresses, thus if CVA is set, then the corresponding CSD is also set. This is only used in Normal
and Loop1 mode tracing. This bit has no meaning in Pure PC mode.
0 Indexed jump destination address
1 Vector destination address
Data Invalid Indicator — This bit indicates if the trace buffer entry is invalid. It is only used when tracing from
both sources in Normal, Loop1 and Pure PC modes, to indicate that the CPU12X trace buffer entry is valid.
0 Trace buffer entry is invalid
1 Trace buffer entry is valid
CPU12X Free Cycle Indicator — This bit indicates if the stored CPU12X address corresponds to a free cycle.
This bit only contains valid information when tracing the XGATE accesses in Detail Mode.
0 Stored information corresponds to free cycle
1 Stored information does not correspond to free cycle
CFREE
CSD
Bit 7
Bit 7
Bit 6
Bit 6
CSZ
CVA
Figure 8-25. CPU12X Information Byte CINF
MC9S12XE-Family Reference Manual Rev. 1.25
Table 8-46. CXINF Field Descriptions
Figure 8-26. Information Byte CXINF
Table 8-45. CINF Field Descriptions
CRW
Bit 5
Bit 5
0
COCF
Bit 4
CDV
Bit 4
Description
Description
XACK
Bit 3
Bit 3
0
Bit 2
Bit 2
XSZ
0
Chapter 8 S12X Debug (S12XDBGV3) Module
XRW
Bit 1
Bit 1
0
XOCF
Bit 0
Bit 0
0
339