MCF5307AI90B Freescale Semiconductor, MCF5307AI90B Datasheet - Page 207

• Manufacturer Part Number: MCF5307AI90B
• Description: IC MPU 32BIT COLDF 90MHZ 208FQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF530xr

Specifications of MCF5307AI90B

• Core Processor: Coldfire V3
• Core Size: 32-Bit
• Speed: 90MHz
• Connectivity: EBI/EMI, I²C, UART/USART
• Peripherals: DMA, POR, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 208-FQFP
• Maximum Clock Frequency: 90 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 90MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: FQFP
• Program Memory Size: 8KB
• Cpu Speed: 90MHz
• Embedded Interface Type: I2C, UART
• Digital Ic Case Style: FQFP
• No. Of Pins: 208
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

determines the relative priority of competing devices. A device loses arbitration if it sends
logic high while another sends logic low; it immediately switches to slave-receive mode
and stops driving SDA. In this case, the transition from master to slave mode does not
generate a STOP condition. Meanwhile, hardware sets I2SR[IAL] to indicate loss of
arbitration.
8.4.2 Clock Synchronization
Because wire-AND logic is used, a high-to-low transition on SCL affects devices
connected to the bus. Devices start counting their low period when the master drives SCL
low. When a device clock goes low, it holds SCL low until the clock high state is reached.
However, the low-to-high change in this device clock may not change the state of SCL if
another device clock is still in its low period. Therefore, the device with the longest low
period holds the synchronized clock SCL low. Devices with shorter low periods enter a high
wait state during this time (See Figure 8-4). When all devices involved have counted off
their low period, the synchronized clock SCL is released and pulled high. There is then no
difference between device clocks and the state of SCL, so all of the devices start counting
their high periods. The first device to complete its high period pulls SCL low again.
8.4.3 Handshaking
The clock synchronization mechanism can be used as a handshake in data transfers. Slave
devices can hold SCL low after completing one byte transfer (9 bits). In such a case, the
clock mechanism halts the bus clock and forces the master clock into wait states until the
slave releases SCL.
8.4.4 Clock Stretching
Slaves can use the clock synchronization mechanism to slow down the transfer bit rate.
After the master has driven SCL low, the slave can drive SCL low for the required period
and then release it. If the slave SCL low period is longer than the master SCL low period,
the resulting SCL bus signal low period is stretched.
SCL1
SCL2
SCL
Freescale Semiconductor, Inc.
Figure 8-4. Synchronized Clock SCL
For More Information On This Product,
Internal Counter Reset
Go to: www.freescale.com
Chapter 8. I
2
Wait
C Module
Start counting high period
I
2
C Protocol
8-5