MCF5307AI90B Freescale Semiconductor, MCF5307AI90B Datasheet - Page 267

• Manufacturer Part Number: MCF5307AI90B
• Description: IC MPU 32BIT COLDF 90MHZ 208FQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF530xr

Specifications of MCF5307AI90B

• Core Processor: Coldfire V3
• Core Size: 32-Bit
• Speed: 90MHz
• Connectivity: EBI/EMI, I²C, UART/USART
• Peripherals: DMA, POR, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 208-FQFP
• Maximum Clock Frequency: 90 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 90MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: FQFP
• Program Memory Size: 8KB
• Cpu Speed: 90MHz
• Embedded Interface Type: I2C, UART
• Digital Ic Case Style: FQFP
• No. Of Pins: 208
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

11.4.5 Initialization Sequence
Synchronous DRAMs have a prescribed initialization sequence. The DRAM controller
supports this sequence with the following procedure:
11.4.5.1 Mode Register Settings
It is possible to configure the operation of SDRAMs, namely their burst operation and CAS
latency, through the SDRAM component’s mode register. CAS latency is a function of the
speed of the SDRAM and the bus clock of the DRAM controller. The DRAM controller
operates at a CAS latency of 1, 2, or 3.
Although the MCF5307 DRAM controller supports bursting operations, it does not use the
bursting features of the SDRAMs. Because the MCF5307 can burst operand sizes of 1, 2,
4, or 16 bytes long, the concept of a fixed burst length in the SDRAMs mode register
becomes problematic. Therefore, the MCF5307 DRAM controller generates the burst
cycles rather than the SDRAM device. Because the MCF5307 generates a new address and
a
should be set either to a burst length of one or to not burst. This allows bursting to be
controlled by the MCF5307 instead.
The SDRAM mode register is written by setting the associated block’s DACR[IMRS].
First, the base address and mask registers must be set to the appropriate configuration to
allow the mode register to be set. Note that improperly set DMR mask bits may prevent
access to the mode register address. Thus, the user should determine the mapping of the
mode register address to the MCF5307 address bits to find out if an access is blocked. If the
DMR setting prohibits mode register access, the DMR should be reconfigured to enable the
access and then set to its necessary configuration after the
READ
1. SDRAM control signals are reset to idle state. Wait the prescribed period after reset
2. Initialize the DCR, DACR, and DMR in their operational configuration. Do not yet
3. Issue a
4. Enable refresh (set DACR[RE]) and wait for at least 8 refreshes to occur.
5. Before issuing the
6. Issue the
before any action is taken on the SDRAMs. This is normally around 100 µs.
enable
SDRAM location. Wait the time (determined by t
modified to allow the
SDRAM. Note that mode register settings are driven on the SDRAM address bus, so
care must be taken to change DMR[BAM] if the mode register configuration does
not fall in the address range determined by the address mask bits. After the mode
register is set, DMR mask bits can be restored to their desired configuration.
or
WRITE
PALL
PALL
MRS
command for each transfer within the burst, the SDRAM mode register
or
command to the SDRAMs by setting DCR[IP] and accessing a
Chapter 11. Synchronous/Asynchronous DRAM Controller Module
command by setting DACR[IMRS] and accessing a location in the
REF
Freescale Semiconductor, Inc.
For More Information On This Product,
MRS
commands.
MRS
command, determine if the DMR mask bits need to be
Go to: www.freescale.com
to execute properly
RP
MRS
) before any other execution.
command executes.
Synchronous Operation
11-33