pc87591l National Semiconductor Corporation, pc87591l Datasheet - Page 124
![no-image](/images/no-image-200.jpg)
pc87591l
Manufacturer Part Number
pc87591l
Description
Lpc Mobile Embedded Controllers
Manufacturer
National Semiconductor Corporation
Datasheet
1.PC87591L.pdf
(437 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PC87591L
Manufacturer:
NS
Quantity:
5 510
Company:
Part Number:
PC87591L
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
pc87591l-VPCN01
Manufacturer:
NSC
Quantity:
5 510
Part Number:
pc87591l-VPCN01
Manufacturer:
NS/国半
Quantity:
20 000
- Current page: 124 of 437
- Download datasheet (3Mb)
www.national.com
Embedded Controller Modules
Power Modes
The PS/2 interface is active only when the PC87591x is in Active mode. The shift mechanism should be disabled before
entering Idle mode. In Idle mode, the state of output signals cannot be changed (i.e., the firmware cannot write to PSOSIG
register, and the shift mechanism does not function).
When the PC87591x needs to wake up on a Start bit detection by the MIWU, the PS/2 channels that may serve as wake-up
event sources must be enabled before entering Idle mode. To enable them, set to 1 their corresponding CLK bits in PSOSIG
register.
The MIWU module can be used to identify a start bit in Idle mode and to return the PC87591x to Active mode. The MIWU
receives PSCLK4-1 and PSDAT4-1 signals as inputs (see Table 17 on page 105). The MIWU should be programed to iden-
tify a falling edge on the clock or data lines of the enabled channels. In this configuration, a start bit causes the PC87591x
to switch from Idle mode to Active mode. Once Active mode is reached, the firmware should cancel the transaction just start-
ed and then enable re-transmission of the information by the device.
PS/2 Interface Operation
The PS/2 interface has two basic operating methods: with the shift mechanism disabled and with the shift mechanism en-
abled. The following sections describe how to use the PS/2 interface with each of these operating methods.
4.6.3
The shift mechanism is disabled when EN bit in PSCON register is cleared (0). In this state, the PS/2 clock and data signals
are controlled by the firmware, which performs the PS/2 protocol by manipulating the PS/2 clock and data signals.
Clock Signal Control
CLK4-1 bits in PSOSIG register control the value of the respective clock signals (PSCLK4-1). When one of these bits is
cleared (0), the relevant pin is held low. When set (1), the open-drain output is open and the respective clock signal is either
floating or held high by the pull-up. In this case, an external device can force the respective clock signal low.
When reading PSISIG register, bits RCLK4-1 indicate the current state of the corresponding clock signal.
Data Signal Control
WDAT4-1 bits in PSOSIG register control the value of the respective data signals (PSDAT4-1). When one of these bits is
cleared (0), the relevant data signal is held low. When set (1), the open-drain output is open and the respective data signal
is held high by the pull-up. In this case, an external device can force the respective data signal low.
When reading PSISIG register, bits RDAT4-1 indicate the current state of the corresponding data signal.
Interrupt Generation
When DSMIE bit in PSIEN register is set (1), the clock input signals are connected to the Interrupt Control Unit (ICU) for an
interrupt driven PS/2 protocol. The four interrupts that are generated are PSINT4-1 for channels 4-1, respectively.
The ICU should be programed to detect a falling edge on each of the clock signals. Disabling a channel by writing 0 to the
clock control signals (CLK4-1) may cause a falling edge on a clock signal. When such an interrupt is not desired, clear the
clock control bit (0); then clear the respective pending bit in the ICU (or in the MIWU, for PSINT4). This should be done while
interrupts are disabled. For more details about the ICU, see Section 4.3 on page 98.
Operating With the Shift Mechanism Disabled
SOT bit (PSTAT)
EOT bit (PSTAT)
DSMIE bit (PSIEN)
EOTIE bit (PSIEN)
SOTIE bit (PSIEN)
PSCLK4
PSCLK1
PSCLK2
PSCLK3
Figure 40. PS/2 Interface Interrupt Signals
(Continued)
124
* Use PSCLK4 in the MIWU.
PSINT1
PSINT2
PSINT4*
PSINT3
Revision 1.07
Related parts for pc87591l
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![mma1270keg](/images/no-image3.png)
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC12034](/images/no-image3.png)
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2350](/images/no-image3.png)
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2324](/images/no-image3.png)
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2301](/images/no-image3.png)
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![NDS8963](/images/no-image3.png)
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM1201](/images/no-image3.png)
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM3501TL-16](/images/no-image3.png)
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![AD9621](/images/no-image3.png)
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM2403](/images/no-image3.png)
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM592M](/images/no-image3.png)
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC10061](/images/no-image3.png)
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS36277TMX](/images/no-image3.png)
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS3654](/images/no-image3.png)
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS3662](/images/no-image3.png)
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: