ATUC128L4U Atmel Corporation, ATUC128L4U Datasheet - Page 366

• Manufacturer Part Number: ATUC128L4U
• Manufacturer: Atmel Corporation

Specifications of ATUC128L4U

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

17.4
17.5
17.5.1
17.5.2
17.5.3
17.5.4
17.5.5
17.6
17.6.1
32142A–12/2011
I/O Lines Description
Product Dependencies
Functional Description
I/O Lines
Power Management
Clocks
Interrupts
Debug Operation
External Interrupts
Table 17-1.
In order to use this module, other parts of the system must be configured correctly, as described
below.
The external interrupt pins (EXTINTn and NMI) may be multiplexed with I/O Controller lines. The
programmer must first program the I/O Controller to assign the desired EIC pins to their periph-
eral function. If I/O lines of the EIC are not used by the application, they can be used for other
purposes by the I/O Controller.
It is only required to enable the EIC inputs actually in use. If an application requires two external
interrupts, then only two I/O lines will be assigned to EIC inputs.
All interrupts are available in all sleep modes as long as the EIC module is powered. However, in
sleep modes where CLK_SYNC is stopped, the interrupt must be configured to asynchronous
mode.
The clock for the EIC bus interface (CLK_EIC) is generated by the Power Manager. This clock is
enabled at reset, and can be disabled in the Power Manager.
The filter and synchronous edge/level detector runs on a clock which is stopped in any of the
sleep modes where the system RC oscillator (RCSYS) is not running. This clock is referred to as
CLK_SYNC.
The external interrupt request lines are connected to the interrupt controller. Using the external
interrupts requires the interrupt controller to be programmed first.
Using the Non-Maskable Interrupt does not require the interrupt controller to be programmed.
When an external debugger forces the CPU into debug mode, the EIC continues normal opera-
tion. If the EIC is configured in a way that requires it to be periodically serviced by the CPU
through interrupts or similar, improper operation or data loss may result during debugging.
The external interrupts are not enabled by default, allowing the proper interrupt vectors to be set
up by the CPU before the interrupts are enabled.
Pin Name
NMI
EXTINTn
I/O Lines Description
Pin Description
Non-Maskable Interrupt
External Interrupt
ATUC64/128/256L3/4U
Type
Input
Input
366