ATUC128L4U Atmel Corporation, ATUC128L4U Datasheet - Page 818

• Manufacturer Part Number: ATUC128L4U
• Manufacturer: Atmel Corporation

Specifications of ATUC128L4U

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32.4
32.5
32.5.1
32.5.2
32.5.3
32.6
32.6.1
32142A–12/2011
I/O Lines Description
Product Dependencies
Functional Description
I/O Lines
Clocks
Debug Operation
Enabling the Lookup Table Inputs
Table 32-1.
Each LUT have 4 inputs and one output. The inputs and outputs for the LUTs are mapped
sequentially to the inputs and outputs. This means that LUT0 is connected to IN0 to IN3 and
OUT0. LUT1 is connected to IN4 to IN7 and OUT1. In general, LUTn is connected to IN[4n] to
IN[4n+3] and OUTn.
In order to use this module, other parts of the system must be configured correctly, as described
below.
The pins used for interfacing the GLOC may be multiplexed with I/O Controller lines. The pro-
grammer must first program the I/O Controller to assign the desired GLOC pins to their
peripheral function. If I/O lines of the GLOC are not used by the application, they can be used for
other purposes by the I/O Controller.
It is only required to enable the GLOC inputs and outputs actually in use. Pullups for pins config-
ured to be used by the GLOC will be disabled.
The clock for the GLOC bus interface (CLK_GLOC) is generated by the Power Manager. This
clock is enabled at reset, and can be disabled in the Power Manager. It is recommended to dis-
able the GLOC before disabling the clock, to avoid freezing the module in an undefined state.
Additionally, the GLOC depends on a dedicated Generic Clock (GCLK). The GCLK can be set to
a wide range of frequencies and clock sources, and must be enabled by the System Control
Interface (SCIF) before the GLOC filter can be used.
When an external debugger forces the CPU into debug mode, the GLOC continues normal
operation.
Since the inputs to each lookup table (LUT) unit can be multiplexed with other peripherals, each
input must be explicitly enabled by writing a one to the corresponding enable bit (AEN) in the
corresponding Control Register (CR).
If no inputs are enabled, the output OUTn will be the least significant bit in the TRUTHn register.
Pin Name
IN0-INm
OUT0-OUTn
I/O Lines Description
Output from lookup tables
Pin Description
Inputs to lookup tables
ATUC64/128/256L3/4U
Type
Input
Output
818