ATUC128L4U Atmel Corporation, ATUC128L4U Datasheet - Page 885

• Manufacturer Part Number: ATUC128L4U
• Manufacturer: Atmel Corporation

Specifications of ATUC128L4U

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

34.6.7
Table 34-30. aWire Command Summary
Table 34-31. Command/Response Description Notation
34.6.7.1
32142A–12/2011
COMMAND
Command/Response
Command/Response value
Additional data
Possible responses
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x80
0x81
0x82
0x83
0x84
aWire Command Summary
AYA
JTAG_ID
MEMORY_SPEED_REQUEST
RESET
Instruction
AYA
STATUS_REQUEST
TUNE
CHIP_ERASE
DISABLE
2_PIN_MODE
MEMORY_WRITE
MEMORY_READ
HALT
SET_GUARD_TIME
The implemented aWire commands are shown in the table below. The responses from the AW
are listed in
All aWire commands are described below, with a summary in table form.
This command asks the AW: “Are you alive”, where the AW should respond with an
acknowledge.
Table 34-32. AYA Details
Command
Command value
Additional data
Possible responses
Description
Shows the command/response value to put into the command/response field of the packet.
Shows the format of the optional data field if applicable.
Shows the possible responses for this command.
Section
34.6.8.
Description
“Are you alive”.
Asks AW to return the JTAG IDCODE.
Request a status message from the AW.
Tell the AW to report the current baud rate.
Reports the speed difference between the aWire control and the SAB clock
domains.
Erases the flash and all volatile memories.
Disables the AW.
Enables the DATAOUT pin and puts the aWire in 2-pin mode, where all
responses are sent on the DATAOUT pin.
Writes words, halfwords, or bytes to the SAB.
Reads words, halfwords, or bytes from the SAB.
Issues a halt command to the device.
Issues a reset to the Reset Controller.
Sets the guard time for the AW.
Details
0x01
N/A
0x40: ACK
0x41: NACK
(Section
(Section
ATUC64/128/256L3/4U
34.6.8.1)
34.6.8.2)
885