HD6432646 Hitachi, HD6432646 Datasheet - Page 721
HD6432646
Manufacturer Part Number
HD6432646
Description
(HD64F264x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432646.pdf
(1155 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HD6432646A52FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6432646B37FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6432646B67FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
HD6432646B99FCJ
Manufacturer:
MOT
Quantity:
44
Part Number:
HD6432646B99FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
HD6432646C41FCJ
Manufacturer:
RENESAS
Quantity:
1 954
Part Number:
HD6432646C41FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
HD6432646C64FCJ
Manufacturer:
RENESAS
Quantity:
1 500
Company:
Part Number:
HD6432646C90FCJV
Manufacturer:
RENESAS
Quantity:
3 967
Company:
Part Number:
HD6432646D08FCJV
Manufacturer:
RENESAS
Quantity:
1 700
- Current page: 721 of 1155
- Download datasheet (5Mb)
20.7.3
When erasing flash memory, the single-block erase flowchart shown in figure 20-12 should be
followed.
The wait times after bits are set or cleared in the flash memory control register 1 (FLMCR1) and
the maximum number of erase operations (N) are shown in table 23-10 in section 23.7, Flash
Memory Characteristics.
To erase flash memory contents, make a 1-bit setting for the flash memory area to be erased in
erase block register 1 and 2 (EBR1, EBR2) at least (t
FLMCR1. Next, the watchdog timer (WDT) is set to prevent overerasing due to program
runaway, etc. Set a value greater than (t
Preparation for entering erase mode (erase setup) is performed next by setting the ESU bit in
FLMCR1. The operating mode is then switched to erase mode by setting the E bit in FLMCR1
after the elapse of at least (t
erase time. Ensure that the erase time does not exceed (t
Note: With flash memory erasing, preprogramming (setting all memory data in the memory to
20.7.4
In erase-verify mode, data is read after memory has been erased to check whether it has been
correctly erased.
After the elapse of the fixed erase time, clear the E bit in FLMCR1, then wait for at least (t
before clearing the ESU bit to exit erase mode. After exiting erase mode, the watchdog timer
setting is also cleared. The operating mode is then switched to erase-verify mode by setting the
EV bit in FLMCR1. Before reading in erase-verify mode, a dummy write of H'FF data should be
made to the addresses to be read. The dummy write should be executed after the elapse of (t
or more. When the flash memory is read in this state (verify data is read in 16-bit units), the data at
the latched address is read. Wait at least (t
read operation. If the read data has been erased (all 1), a dummy write is performed to the next
address, and erase-verify is performed. If the read data is unerased, set erase mode again, and
repeat the erase/erase-verify sequence as before. The maximum number of repetitions of the
erase/erase-verify sequence is indicated by the maximum erase count (N). When verification is
completed, exit erase-verify mode, and wait for at least (t
all the erase blocks, clear the SWE bit in FLMCR1, and leave a wait time of at least (t
If erasing multiple blocks, set a single bit in EBR1/EBR2 for the next block to be erased, and
repeat the erase/erase-verify sequence as before.
be erased to all 0) is not necessary before starting the erase procedure.
Erase Mode
Erase-Verify Mode
sesu
) µs. The time during which the E bit is set is the flash memory
se
) ms + (t
sevr
) µs after the dummy write before performing this
sesu
sswe
+ t
) µs after setting the SWE bit to 1 in
ce
se
) ms.
cev
+ t
) µs. If erasure has been completed on
cesu
) µs as the WDT overflow period.
cswe
) µs.
ce
sev
) µs
) µs
687
Related parts for HD6432646
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: