AT91SAM7S256D-AU Atmel, AT91SAM7S256D-AU Datasheet - Page 453
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
AT91SAM7S256D-AU
Manufacturer Part Number
AT91SAM7S256D-AU
Description
ARM Microcontrollers - MCU 256K Flash SRAM 64K ARM based MCU
Manufacturer
Atmel
Series
SAM7S256r
Datasheet
1.AT91SAM7S256D-AU.pdf
(775 pages)
Specifications of AT91SAM7S256D-AU
Rohs
yes
Core
ARM
Processor Series
AT91SAM
Data Bus Width
16 bit/32 bit
Maximum Clock Frequency
55 MHz
Program Memory Size
256 KB
Data Ram Size
64 KB
On-chip Adc
Yes
Operating Supply Voltage
3 V to 3.6 V
Operating Temperature Range
- 40 C to + 85 C
Package / Case
LQFP-64
Mounting Style
SMD/SMT
Interface Type
2-Wire, I2S, SPI, USART
Length
7 mm
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT91SAM7S256D-AU
Manufacturer:
ATMEL
Quantity:
101
- Current page: 453 of 775
- Download datasheet (5Mb)
33.5.7
33.5.8
33.5.9
•
•
The channel can also be configured to have an external trigger. In Capture Mode, the external trigger signal can be
selected between TIOA and TIOB. In Waveform Mode, an external event can be programmed on one of the follow-
ing signals: TIOB, XC0, XC1 or XC2. This external event can then be programmed to perform a trigger by setting
ENETRG in TC_CMR.
If an external trigger is used, the duration of the pulses must be longer than the master clock period in order to be
detected.
Regardless of the trigger used, it will be taken into account at the following active edge of the selected clock. This
means that the counter value can be read differently from zero just after a trigger, especially when a low frequency
signal is selected as the clock.
This mode is entered by clearing the WAVE parameter in TC_CMR (Channel Mode Register).
Capture Mode allows the TC channel to perform measurements such as pulse timing, frequency, period, duty cycle
and phase on TIOA and TIOB signals which are considered as inputs.
Figure 33-5
Registers A and B (RA and RB) are used as capture registers. This means that they can be loaded with the counter
value when a programmable event occurs on the signal TIOA.
The LDRA parameter in TC_CMR defines the TIOA edge for the loading of register A, and the LDRB parameter
defines the TIOA edge for the loading of Register B.
RA is loaded only if it has not been loaded since the last trigger or if RB has been loaded since the last loading of
RA.
RB is loaded only if RA has been loaded since the last trigger or the last loading of RB.
Loading RA or RB before the read of the last value loaded sets the Overrun Error Flag (LOVRS) in TC_SR (Status
Register). In this case, the old value is overwritten.
In addition to the SYNC signal, the software trigger and the RC compare trigger, an external trigger can be defined.
The ABETRG bit in TC_CMR selects TIOA or TIOB input signal as an external trigger. The ETRGEDG parameter
defines the edge (rising, falling or both) detected to generate an external trigger. If ETRGEDG = 0 (none), the
external trigger is disabled.
Capture Operating Mode
Capture Registers A and B
Trigger Conditions
SYNC: Each channel has a synchronization signal SYNC. When asserted, this signal has the same effect as a
software trigger. The SYNC signals of all channels are asserted simultaneously by writing TC_BCR (Block
Control) with SYNC set.
Compare RC Trigger: RC is implemented in each channel and can provide a trigger when the counter value
matches the RC value if CPCTRG is set in TC_CMR.
shows the configuration of the TC channel when programmed in Capture Mode.
SAM7S Series [DATASHEET]
6175M–ATARM–26-Oct-12
453
Related parts for AT91SAM7S256D-AU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AT91SAM7S-EK](/photos/9/20/92029/at91sam7s-ek_tmb.jpg)
Part Number:
Description:
KIT EVAL FOR ARM AT91SAM7S
Manufacturer:
Atmel
Datasheet:
![KSK-AT91SAM7S-PL](/photos/15/92/159245/largeiarsystemskickstartkit_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools KICKSTART KIT ATMEL AT91SAM7S
Manufacturer:
IAR Systems
![AT91SAM9R64-CU](/photos/12/13/121356/144-lfbga_tmb.jpg)
Part Number:
Description:
MCU ARM9 64K SRAM 144-LFBGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM7A3-AU](/photos/6/76/67646/313-100-lqfp_tmb.jpg)
Part Number:
Description:
IC ARM7 MCU FLASH 256K 100LQFP
Manufacturer:
Atmel
Datasheet:
![AT91SAM9G20B-CU](/photos/12/13/121366/217-lfbga_tmb.jpg)
Part Number:
Description:
IC ARM9 MPU 217-LFBGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM9261B-CU](/photos/12/13/121366/217-lfbga_tmb.jpg)
Part Number:
Description:
MCU ARM9 ULTRA LOW PWR 217-LFBGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM9G45-CU](/photos/12/13/121367/324-tfbga-pkg_tmb.jpg)
Part Number:
Description:
MCU ARM9 324-TFBGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM9G10-CU](/photos/12/13/121366/217-lfbga_tmb.jpg)
Part Number:
Description:
IC MCU ARM9 SAMPLING 217CBGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM9260B-CU](/photos/12/13/121366/217-lfbga_tmb.jpg)
Part Number:
Description:
IC ARM9 MCU 217-LFBGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM9260B-QU](/photos/6/73/67311/313-208-pqfp_tmb.jpg)
Part Number:
Description:
IC ARM9 MCU 208-PQFP
Manufacturer:
Atmel
Datasheet:
![AT91SAM7X512-AU](/photos/6/76/67646/313-100-lqfp_tmb.jpg)
Part Number:
Description:
MCU ARM 512K HS FLASH 100-LQFP
Manufacturer:
Atmel
Datasheet:
![AT91SAM7X512-CU](/photos/6/89/68968/313-100-cbga_tmb.jpg)
Part Number:
Description:
MCU ARM 512K HS FLASH 100-TFBGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM9263B-CU](/photos/12/13/121367/324-tfbga-pkg_tmb.jpg)
Part Number:
Description:
IC ARM9 MCU 200 MHZ 324-TFBGA
Manufacturer:
Atmel
Datasheet:
![AT91RM9200-CJ-002](/photos/12/32/123245/256-bga_tmb.jpg)
Part Number:
Description:
IC ARM MCU 16BIT 128K 256BGA
Manufacturer:
Atmel
Datasheet:
![AT91SAM7S128-AU-001](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
IC ARM7 MCU 32BIT 128K 64LQFP
Manufacturer:
Atmel
Datasheet: