MA180025 Microchip Technology, MA180025 Datasheet - Page 310

MODULE PLUG-IN PIC18F87J90 PIM

MA180025

Manufacturer Part Number
MA180025
Description
MODULE PLUG-IN PIC18F87J90 PIM
Manufacturer
Microchip Technology
Series
PIC®r
Datasheets

Specifications of MA180025

Accessory Type
Plug-In Module (PIM) - PIC18F87J90
Product
Microcontroller Modules
Silicon Manufacturer
Microchip
Core Architecture
PIC
Core Sub-architecture
PIC18
Silicon Core Number
PIC18F
Silicon Family Name
PIC18FxxJxx
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
PICDEM LCD 2 Demonstration Board (DM163030)
For Use With
DM163030 - KIT DEV PICDEM LCD2
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MA180025
Manufacturer:
Microchip Technology
Quantity:
135
Part Number:
MA180025
Manufacturer:
MICROCHIP
Quantity:
12 000
PIC18F87J90 FAMILY
24.1
The CTMU works by using a fixed current source to
charge a circuit. The type of circuit depends on the type
of measurement being made. In the case of charge
measurement, the current is fixed and the amount of
time the current is applied to the circuit is fixed. The
amount of voltage read by the A/D is then a measure-
ment of the capacitance of the circuit. In the case of
time measurement, the current, as well as the capaci-
tance of the circuit, are fixed. In this case, the voltage
read by the A/D is then representative of the amount of
time elapsed from the time the current source starts
and stops charging the circuit.
If the CTMU is being used as a time delay, both capaci-
tance and current source are fixed, as well as the voltage
supplied to the comparator circuit. The delay of a signal
is determined by the amount of time it takes the voltage
to charge to the comparator threshold voltage.
24.1.1
The operation of the CTMU is based on the equation
for charge:
More simply, the amount of charge measured in
coulombs in a circuit is defined as current in amperes
(I) multiplied by the amount of time in seconds that the
current flows (t). Charge is also defined as the capaci-
tance in farads (C) multiplied by the voltage of the
circuit (V). It follows that:
The CTMU module provides a constant, known current
source. The A/D Converter is used to measure (V) in
the equation, leaving two unknowns: capacitance (C)
and time (t). The above equation can be used to calcu-
late capacitance or time, by either relationship using
the known fixed capacitance of the circuit:
or by:
using a fixed time that the current source is applied to
the circuit.
24.1.2
At the heart of the CTMU is a precision current source,
designed to provide a constant reference for measure-
ments. The level of current is user-selectable across
three ranges or a total of two orders of magnitude, with
the ability to trim the output in ±2% increments
(nominal). The current range is selected by the
IRNG<1:0> bits (CTMUICON<1:0>), with a value of
‘00’ representing the lowest range.
DS39933D-page 310
CTMU Operation
THEORY OF OPERATION
CURRENT SOURCE
C = I •
t = (C • V)/I
C = (I • t)/V
I • t = C • V
dV
dT
Current trim is provided by the ITRIM<5:0> bits
(CTMUICON<7:2>). These six bits allow trimming of
the current source in steps of approximately 2% per
step. Note that half of the range adjusts the current
source positively and the other half reduces the current
source. A value of ‘000000’ is the neutral position (no
change). A value of ‘100000’ is the maximum negative
adjustment (approximately -62%) and ‘011111’ is the
maximum positive adjustment (approximately +62%).
24.1.3
CTMU measurements are controlled by edge events
occurring on the module’s two input channels. Each
channel, referred to as Edge 1 and Edge 2, can be con-
figured to receive input pulses from one of the edge
input pins (CTEDG1 and CTEDG2) or the CCPx
Special Event Triggers. The input channels are level-
sensitive, responding to the instantaneous level on the
channel rather than a transition between levels. The
inputs are selected using the EDG1SEL and EDG2SEL
bit pairs (CTMUCONL<3:2, 6:5>).
In addition to source, each channel can be configured for
event polarity using the EDGE2POL and EDGE1POL
bits (CTMUCONL<7,4>). The input channels can also
be filtered for an edge event sequence (Edge 1 occur-
ring before Edge 2) by setting the EDGSEQEN bit
(CTMUCONH<2>).
24.1.4
The CTMUCON register also contains two status bits,
EDG2STAT and EDG1STAT (CTMUCONL<1:0>).
Their primary function is to show if an edge response
has occurred on the corresponding channel. The
CTMU automatically sets a particular bit when an edge
response is detected on its channel. The level-sensitive
nature of the input channels also means that the status
bits become set immediately if the channel’s configura-
tion is changed and is the same as the channel’s
current state.
The module uses the edge status bits to control the cur-
rent source output to external analog modules (such as
the A/D Converter). Current is only supplied to external
modules when only one (but not both) of the status bits
is set, and shuts current off when both bits are either
set or cleared. This allows the CTMU to measure cur-
rent only during the interval between edges. After both
status bits are set, it is necessary to clear them before
another measurement is taken. Both bits should be
cleared simultaneously, if possible, to avoid re-enabling
the CTMU current source.
In addition to being set by the CTMU hardware, the
edge status bits can also be set by software. This is
also the user’s application to manually enable or dis-
able the current source. Setting either one (but not
both) of the bits enables the current source. Setting or
clearing both bits at once disables the source.
EDGE SELECTION AND CONTROL
EDGE STATUS
 2010 Microchip Technology Inc.

Related parts for MA180025