MA180025 Microchip Technology, MA180025 Datasheet - Page 95

MODULE PLUG-IN PIC18F87J90 PIM

MA180025

Manufacturer Part Number
MA180025
Description
MODULE PLUG-IN PIC18F87J90 PIM
Manufacturer
Microchip Technology
Series
PIC®r
Datasheets

Specifications of MA180025

Accessory Type
Plug-In Module (PIM) - PIC18F87J90
Product
Microcontroller Modules
Silicon Manufacturer
Microchip
Core Architecture
PIC
Core Sub-architecture
PIC18
Silicon Core Number
PIC18F
Silicon Family Name
PIC18FxxJxx
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
PICDEM LCD 2 Demonstration Board (DM163030)
For Use With
DM163030 - KIT DEV PICDEM LCD2
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MA180025
Manufacturer:
Microchip Technology
Quantity:
135
Part Number:
MA180025
Manufacturer:
MICROCHIP
Quantity:
12 000
7.5
The programming block is 32 words or 64 bytes.
Programming one word or two bytes at a time is also
supported.
Table writes are used internally to load the holding
registers needed to program the Flash memory. There
are 64 holding registers used by the table writes for
programming.
Since the Table Latch (TABLAT) is only a single byte, the
TBLWT instruction may need to be executed 64 times for
each programming operation (if WPROG = 0). All of the
table write operations will essentially be short writes
because only the holding registers are written. At the
end of updating the 64 holding registers, the EECON1
register must be written to in order to start the
programming operation with a long write.
The long write is necessary for programming the inter-
nal Flash. Instruction execution is halted while in a long
write cycle. The long write will be terminated by the
internal programming timer.
FIGURE 7-5:
7.5.1
The sequence of events for programming an internal
program memory location should be:
1.
2.
3.
4.
5.
6.
7.
 2010 Microchip Technology Inc.
TBLPTR = xxxxx0
Read 1024 bytes into RAM.
Update data values in RAM as necessary.
Load Table Pointer register with the address
being erased.
Execute the erase procedure.
Load the Table Pointer register with the address
of the first byte being written, minus 1.
Write the 64 bytes into the holding registers with
auto-increment.
Set the WREN bit (EECON1<2>) to enable byte
writes.
Writing to Flash Program Memory
FLASH PROGRAM MEMORY WRITE
SEQUENCE
Holding Register
TABLE WRITES TO FLASH PROGRAM MEMORY
8
TBLPTR = xxxxx1
Holding Register
8
Program Memory
Write Register
TBLPTR = xxxxx2
TABLAT
PIC18F87J90 FAMILY
The on-chip timer controls the write time. The
write/erase voltages are generated by an on-chip
charge pump, rated to operate over the voltage range
of the device.
8.
9.
10. Write 0AAh to EECON2.
11. Set the WR bit. This will begin the write cycle.
12. The CPU will stall for the duration of the write for
13. Re-enable interrupts.
14. Repeat steps 6 through 13 until all 1024 bytes
15. Verify the memory (table read).
An example of the required code is shown in
Example 7-3 on the following page.
Note:
Holding Register
Note 1: Unlike previous PIC18 Flash devices,
Disable interrupts.
Write 55h to EECON2.
T
are written to program memory.
IW
(parameter D133A).
2: To maintain the endurance of the program
8
Before setting the WR bit, the Table
Pointer address needs to be within the
intended address range of the 64 bytes in
the holding register.
members of the PIC18F87J90 family do
not reset the holding registers after a
write occurs. The holding registers must
be cleared or overwritten before a
programming sequence.
memory cells, each Flash byte should not
be programmed more than one time
between
attempting to modify the contents of the
target cell a second time, an erase of the
target, or a bulk erase of the entire
memory, must be performed.
erase
TBLPTR = xxxx3F
operations.
Holding Register
DS39933D-page 95
8
Before

Related parts for MA180025