LSI53C825AJ LSI, LSI53C825AJ Datasheet - Page 81
LSI53C825AJ
Manufacturer Part Number
LSI53C825AJ
Description
Manufacturer
LSI
Datasheet
1.LSI53C825AJ.pdf
(306 pages)
Specifications of LSI53C825AJ
Lead Free Status / RoHS Status
Not Compliant
- Current page: 81 of 306
- Download datasheet (2Mb)
Table 3.7
3.1.7 Additional Interface Signals
Table 3.8
Name
RSTDIR
BSYDIR
IGS
TGS
Name
TESTIN (Not
available on
LSI53C825AJ)
GPIO0_
FETCH/
SCSI Bus Interface Signals (Cont.)
Additional Interface Signals
53/70/N5
Pin No.
57, NA
Pin No.
Table 3.8
PCI Bus Interface Signals
77
78
75
73
Type Description
I/O
I
describes the signals for the Additional Interface Signals group:
Type Description
O
O
O
O
Test In. When this pin is driven LOW, the LSI53C825A connects
all inputs and outputs to an “AND tree.” The SCSI control
signals and data lines are not connected to the “AND tree.” The
output of the “AND tree” is connected to the Test Out pin. This
allows manufacturers to verify chip connectivity and determine
exactly which pins are not properly attached. When the TESTIN
pin is driven LOW, internal pull-ups are enabled on all input,
output, and bidirectional pins, all outputs and bidirectional
signals are 3-stated, and the MAC/_TESTOUT pin is enabled.
Connectivity can be tested by driving one of the LSI53C825A
pins LOW. The MAC/_TESTOUT pin should respond by also
driving LOW.
General Purpose I/O pin. Optionally, when driven LOW, this pin
indicates that the next bus request will be for an opcode fetch.
This pin powers up as a general purpose input.
This pin has two specific purposes in the LSI Logic SDMS
software. SDMS software uses it to toggle SCSI device LEDs,
turning on the LED whenever the LSI53C825A is on the SCSI
bus. SDMS software drives this pin LOW to turn on the LED, or
drives it HIGH to turn off the LED. This signal can also be used
as data I/O for serial EEPROM access. In this case it is used
with the GPIO0 pin, which serves as a clock, and the pin can
be controlled from PCI configuration register 0x35 or observed
from the
Driver Enable Control for SCSI RST/ signal.
Driver Enable Control for SCSI BSY/ signal.
Direction Control for initiator driver group.
Direction Control for target driver group.
General Purpose (GPREG)
register, at address 0x07.
3-11
Related parts for LSI53C825AJ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
BGA 117/RESTRICTED SALE - SELL LSISS9132 INTERPOSER CARD FIRST (CONTACT LSI
Manufacturer:
LSI Computer Systems, Inc.
Part Number:
Description:
Keypad programmable digital lock
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
TOUCH CONTROL LAMP DIMMER
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
32bit/dual 16bit binary up counter with byte multiplexed three-state outputs
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
24-bit quadrature counter
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
Quadrature clock converter
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
Quadrature clock converter
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
Enclosure Services Processor
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
24-bit dual-axis quadrature counter
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
LSI402ZXLSI402ZX digital signal processor
Manufacturer:
LSI Computer Systems, Inc.
Datasheet:
Part Number:
Description:
24 Bit Multimode Counter
Manufacturer:
LSI Computer Systems, Inc.
Datasheet: