TMPA901CMXBG Toshiba, TMPA901CMXBG Datasheet - Page 507

• Manufacturer Part Number: TMPA901CMXBG
• Description: Microcontrollers (MCU) 32-bit RISC MCU 16kb ARM926EJ 16kb 200Mhz
• Manufacturer: Toshiba

Specifications of TMPA901CMXBG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): -
• Rom Type: ROMless
• Ram (kbytes): 32
• Number Of Pins: 177
• Package: BGA
• Vcc: 3V
• Tft Lcd Controller: Y
• Touchscreen Controller: Y
• Usb Host Fs With Phy: Y
• Usb Device Hs With Phy: Y
• Sd Host Controller: -
• Cmos Image Sensor Interface: -
• I2s: 1
• Ssp (ch) Spi: 1
• I2mc/sio (ch): 1
• Uart/sio (ch): 2
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 8
• 10-bit Ad Converter: 4
• 12-bit Da Converter: -
• 16-bit Timer / Counter: 6
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Low-power Modes: Y
• Lead Free Status / Rohs Status: Details

[31:16]
[15]
[14]
[13:12]
[11]
[10]
[9]
[8]
[7]
[6:0]
Bit
[Description]
stage_err
ep_bi_mode
cur_speed[1:0]
Suspend
Configured
Addressed
Default
dev_adr[6:0]
a. <stage_err>
Note 1: The initial value of cur_speed[1:0] (bits [13:12]) after USB_RESET is “0y10” (high-Speed) if the Chirp
Note 2 : About TMPA900CM, EP0: single direction / dual direction . EP1, EP2 and EP3: single direction. only
Symbol
Indicates whether Control transfers finished normally up to the STATUS-Stage.
1 will be set when the Setup-Token is received in DATA-Stage/STATUS-Stage or in the
case of “STALL” transmission. When set, it will be cleared when the next Control transfer
has been finished normally.
0y0: Other than above conditions
0y1: Received the Setup-Token in DATA-Stage/STATUS-Stage or “STALL” transmission.
(1) Device Status Registers
1.
Bit
sequencehas been sucessful, and “0y01” (Full-Speed) if it has failed.
UD2ADR (Address-State register)
RO
R/W
RO
RO
R/W
R/W
R/W
R/W
Type
Undefined
0y0
0y0, (-)
0y01,(Note1)
0y0
0y0
0y0
0y0,(1)
Undefined
0y0000000
TMPA901CM- 506
Reset
Value
Read as undefined. Write as zero.
Indicates whether Control transfers finished normally up to
the STATUS-Stage.
0y0: Other than below conditions
0y1: Received the Setup-Token in
Selects whether to use the endpoint bidirectionally as a
driver. (Note 2)
0y0: Single direction
0y1: Dual direction
Indicates the present transfer mode on the USB bus.
0y00: Reserved
0y10: High-Speed
Indicates whether or not UDC2 is in suspended state.
0y0: Normal,
Sets the present device state of UDC2.
0y001:Default (to be set when the DeviceAddress=0 was
0y010:Addressed (to be set when ConfigurationVallue = 0
0y100:Configured (to be set when the Set_config request is
Read as undefined. Write as zero.
Sets the device address assigned by the host.
DATA-Stage/STATUS-Stage or "STALL" transmission.
specified by the Set_address request in
Default/Address state (this will be set by the hardware
when USB_RESET is received))
was specified by the Set_configuration request after the
Set_address request finished normally and in the
Address/Configured state)
received)
Address = (0xF440_0000) + (0x0200)
Description
0y01: Full-Speed
0y11: Reserved
0y1: Suspended
TMPA901CM
2010-07-29