SAM7SE256 Atmel Corporation, SAM7SE256 Datasheet - Page 341

• Manufacturer Part Number: SAM7SE256
• Manufacturer: Atmel Corporation

Specifications of SAM7SE256

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 48 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 88
• Ext Interrupts: 88
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

31.7.5
Name:
Access:
• RDRF: Receive Data Register Full
0 = No data has been received since the last read of SPI_RDR
1 = Data has been received and the received data has been transferred from the serializer to SPI_RDR since the last read
of SPI_RDR.
• TDRE: Transmit Data Register Empty
0 = Data has been written to SPI_TDR and not yet transferred to the serializer.
1 = The last data written in the Transmit Data Register has been transferred to the serializer.
TDRE equals zero when the SPI is disabled or at reset. The SPI enable command sets this bit to one.
• MODF: Mode Fault Error
0 = No Mode Fault has been detected since the last read of SPI_SR.
1 = A Mode Fault occurred since the last read of the SPI_SR.
• OVRES: Overrun Error Status
0 = No overrun has been detected since the last read of SPI_SR.
1 = An overrun has occurred since the last read of SPI_SR.
An overrun occurs when SPI_RDR is loaded at least twice from the serializer since the last read of the SPI_RDR.
• ENDRX: End of RX buffer
0 = The Receive Counter Register has not reached 0 since the last write in SPI_RCR
1 = The Receive Counter Register has reached 0 since the last write in SPI_RCR
• ENDTX: End of TX buffer
0 = The Transmit Counter Register has not reached 0 since the last write in SPI_TCR
1 = The Transmit Counter Register has reached 0 since the last write in SPI_TCR
• RXBUFF: RX Buffer Full
0 = SPI_RCR
1 = Both SPI_RCR
6222F–ATARM–14-Jan-11
TXBUFE
31
23
15
–
–
–
7
SPI Status Register
(1)
or SPI_RNCR
RXBUFF
(1)
and SPI_RNCR
30
22
14
SPI_SR
Read-only
–
–
–
6
(1)
has a value other than 0.
ENDTX
29
21
13
(1)
–
–
–
5
have a value of 0.
ENDRX
28
20
12
–
–
–
4
OVRES
27
19
11
–
–
–
3
MODF
(1)
(1)
26
18
10
–
–
–
2
or SPI_RNCR
or SPI_TNCR
(1)
SAM7SE512/256/32
(1)
or SPI_RNCR
or SPI_TNCR
TXEMPTY
TDRE
(1)
(1)
25
17
–
–
9
1
.
.
(1)
(1)
.
.
SPIENS
NSSR
RDRF
24
16
–
8
0
341