SAM7SE256 Atmel Corporation, SAM7SE256 Datasheet - Page 63

• Manufacturer Part Number: SAM7SE256
• Manufacturer: Atmel Corporation

Specifications of SAM7SE256

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 48 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 88
• Ext Interrupts: 88
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 13-9.
13.3
Table 13-1.
6222F–ATARM–14-Jan-11
Offset
0x00
0x04
0x08
if (URSTEN = 0) and
Reset Controller (RSTC) User Interface
Peripheral Access
(URSTIEN = 1)
Reset Controller (RSTC) Register Mapping
Reset Controller Status and Interrupt
URSTS
NRSTL
rstc_irq
NRST
MCK
Register
Control Register
Status Register
Mode Register
resynchronization
• RSTTYP field: This field gives the type of the last reset, as explained in previous sections.
• SRCMP bit: This field indicates that a Software Reset Command is in progress and that no
• NRSTL bit: The NRSTL bit of the Status Register gives the level of the NRST pin sampled on
• URSTS bit: A high-to-low transition of the NRST pin sets the URSTS bit of the RSTC_SR
• BODSTS bit: This bit indicates a brownout detection when the brownout reset is disabled
further software reset should be performed until the end of the current one. This bit is
automatically cleared at the end of the current software reset.
each MCK rising edge.
register. This transition is also detected on the Master Clock (MCK) rising edge (see
13-9). If the User Reset is disabled (URSTEN = 0) and if the interruption is enabled by the
URSTIEN bit in the RSTC_MR register, the URSTS bit triggers an interrupt. Reading the
RSTC_SR status register resets the URSTS bit and clears the interrupt.
(bod_rst_en = 0). It triggers an interrupt if the bit BODIEN in the RSTC_MR register enables
the interrupt. Reading the RSTC_SR register resets the BODSTS bit and clears the interrupt.
2 cycle
Name
RSTC_CR
RSTC_SR
RSTC_MR
resynchronization
2 cycle
SAM7SE512/256/32
Read/Write
Read-only
Write-only
Access
RSTC_SR
read
0x0000_0000
0x0000_0000
Reset Value
-
Figure
63