SAM7SE256 Atmel Corporation, SAM7SE256 Datasheet - Page 58

• Manufacturer Part Number: SAM7SE256
• Manufacturer: Atmel Corporation

Specifications of SAM7SE256

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 48 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 88
• Ext Interrupts: 88
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

13.2.4.1
Figure 13-4. Power-up Reset
13.2.4.2
58
SAM7SE512/256/32
periph_nreset
Main Supply
POR output
proc_nreset
(nrst_out)
Power-up Reset
User Reset
SLCK
NRST
MCK
When VDDCORE is powered on, the Main Supply POR cell output is filtered with a start-up
counter that operates at Slow Clock. The purpose of this counter is to ensure that the Slow
Clock oscillator is stable before starting up the device.
The startup time, as shown in
startup time. After the startup time, the reset signals are released and the field RSTTYP in
RSTC_SR reports a Power-up Reset.
When VDDCORE is detected low by the Main Supply POR Cell, all reset signals are asserted
immediately.
The User Reset is entered when a low level is detected on the NRST pin and the bit URSTEN in
RSTC_MR is at 1. The NRST input signal is resynchronized with SLCK to insure proper behav-
ior of the system.
The User Reset is entered as soon as a low level is detected on NRST. The Processor Reset
and the Peripheral Reset are asserted.
The User Reset is left when NRST rises, after a two-cycle resynchronization time and a three-
cycle processor startup. The processor clock is re-enabled as soon as NRST is confirmed high.
When the processor reset signal is released, the RSTTYP field of the Status Register
(RSTC_SR) is loaded with the value 0x4, indicating a User Reset.
T h e
EXTERNAL_RESET_LENGTH Slow Clock cycles, as programmed in the field ERSTL. How-
ever, if NRST does not rise after EXTERNAL_RESET_LENGTH because it is driven low
externally, the internal reset lines remain asserted until NRST actually rises.
N R S T
Startup Time
M a n a g e r
g u a r a n t e e s
Figure
Processor Startup
EXTERNAL RESET LENGTH
= 3 cycles
13-4, is hardcoded to comply with the Slow Clock Oscillator
= 2 cycles
t h a t
t h e
N R S T
l i n e
Freq.
Any
i s
6222F–ATARM–14-Jan-11
a s s e r t e d
f o r