AT91SAM9M10-CU Atmel, AT91SAM9M10-CU Datasheet - Page 59

• Manufacturer Part Number: AT91SAM9M10-CU
• Description: IC MCU 16/32BIT ARM9 324TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9M10-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 400MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 1.1 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 133 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 2 x 16 bit
• Operating Supply Voltage: 1.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9M10-G45-EK
• Controller Family/series: AT91
• No. Of I/o's: 160
• Ram Memory Size: 64KB
• Cpu Speed: 400MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Cpu Family: AT91
• Device Core: ARM926EJ-S
• Device Core Size: 32b
• Frequency (max): 400MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 160
• Number Of Timers - General Purpose: 7
• Operating Supply Voltage (typ): 1.8/2.5/3.3V
• Operating Supply Voltage (max): 1.1/1.95/3.6V
• Operating Supply Voltage (min): 0.9/1.65/1.8/3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 324
• Package Type: TFBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

11.3
11.3.1
11.3.2
6355B–ATARM–21-Jun-10
Device Initialization
Clock at Start Up
Initialization Sequence
At boot start up, the processor clock (PCK) and the master clock (MCK) are found on the slow
clock. The slow clock can be an external 32 kHz crystal oscillator or the internal RC oscillator. By
default the slow clock is the internal RC oscillator. Its frequency is not precise and is between 20
kHz and 40 kHz. Its start up is much faster than an external 32 kHz quartz. If a battery supplies
the backup power and if the external 32 kHz clock was previously started up and selected, the
slow clock at boot is the external 32 kHz quartz oscillator. Refer to the Slow Clock Crystal Oscil-
lator description in the Clock Generator section of the datasheet.
Initialization follows the steps described below:
1. Stack setup for ARM supervisor mode.
2. Main Oscillator Detection: (External crystal or external clock on XIN). The Main Oscil-
3. Main Oscillator Enabling: if an external clock is connected on XIN, the Main Oscillator
4. Main Oscillator Selection: the Master Clock source is switched from Slow Clock to the
5. C variable initialization: non zero-initialized data are initialized in RAM (copy from
6. PLLA initialization: PLLA is configured to allow communication on the USB link for the
lator is disabled at startup (MOSCEN = 0). First it is bypassed (OSCBYPASS set at 1).
Then the MAINRDY bit is polled. Since this bit is raised, the Main Clock Frequency field
is analyzed (MAINF). If the value is bigger than 16, an external clock connected on XIN
is detected. If not, an external quartz connected between XIN and XOUT (whose fre-
quency is unknown at this moment) is detected.
does not need to be started. Otherwise, the OSCBYPASS bit is not set. The Main Oscil-
lator is enabled (MOSCEN = 1) with the maximum start-up time and the MOSC bit is
polled to wait for stabilization.
Main Oscillator without prescaler. The PMC Status Register is polled to wait for MCK
Ready. PCK and MCK are now the Main Oscillator clock.
ROM to RAM). Zero-initialized data are set to 0 in RAM.
SAM-BA Monitor. Its configuration depends on the Main Oscillator source (external
clock or crystal) and on its frequency.
AT91SAM9M10
59