DF2239TF16I Renesas Electronics America, DF2239TF16I Datasheet - Page 599

• Manufacturer Part Number: DF2239TF16I
• Description: MCU 3V 384K I-TEMP 100-TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2200r

Specifications of DF2239TF16I

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: I²C, SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 72
• Program Memory Size: 384KB (384K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Other names: HD64F2239TF16I; HD64F2239TF16I

(c) Setting the IEBus Transmit Message Length Register (IETBFL)
(d) Setting the IEBus Transmit/Runaway Interrupt Enable Register (IEIET)
The above registers can be specified in any order. (The register specification order does not affect
the IEB operation.)
(2) DTC Initialization
1. Set the start address of the RAM which stores the register information necessary for the DTC
2. Set the following data from the start address of the RAM.
3. Set bit DTCEG5 in the DTC enabler register G (DTCERG), and enable the TxRDY interrupt
(3) Slave Transmission Flow
Figure 14.12 shows the slave transmission flow. Numbers in the following description correspond
to the numbers in Figure 14.12.
1. After the IEB and DTC have been initialized, a slave communications request command is
2. The CMX flag is cleared when the slave reception is completed, the slave communications
3. If data up to the control field has been received correctly and if the contents of the control bits
4. The slave then transmits the message length field, and the IEB loads the transmit data in the
Specify the message length bits.
Enable the TxRDY (IETxI), TxS, and TxE (IETSI) interrupts.
transfer in the vector address (H'000004D4) to be accessed a DTC transfer request is
generated.
⎯ Transfer source address (SAR): Start address of the RAM which stores data to be
⎯ Transfer destination address (DAR): Address (H'FFF808) of the IEBus transmit buffer
⎯ Transfer count (CRA): The same value as IETBFL
(IETxI).
Because the TxRDY flag is retained after reset, the DTC transfer is executed when the IETxI is
enabled and the first data field data is written to IETBR. The DTC negates the TxRDY flag
and the DTC transfer of the first byte is completed.
issued from IECMR. During slave reception, the command execution status flag (CMX) in
IEFLG is set and the slave communications request will not be issued.
command is executed, and the SRQ flag is set.
is H'3 or H'7, the transmit start detection flag (TxS) in IETSR register is set to 1. In this case,
the TxS flag is cleared in the TxS interrupt handling routine.
data field from IETBR when the ACK is received. Then the TxRDY flag is set to 1. A DTC
transmitted from the data field.
register (IETBR)
Section 14 IEBus™ Controller (IEB) [H8S/2258 Group]
Rev. 6.00 Mar. 18, 2010 Page 537 of 982
REJ09B0054-0600