M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 158

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
Figure 14.4 Registers IDB0, IDB1, and DTT
Dead Time Timer
Three-Phase Output Buffer Register i (i = 0, 1)
NOTE:
NOTES:
b7
b7
0 0
Apr 14, 2006
1. The values of registers IDB0 and IDB1 are transferred to the three-phase output shift register by a transfer
1. Use the MOV instruction to set the DTT register.
2. The DTT register is enabled when the INV15 bit in the INVC1 register is set to 0 (dead time enabled).
b6
trigger.
After the transfer trigger occurs, the values written in the IDB0 register determine each phase output signal
first. Then the value written in the IDB1 register on the falling edge of timers A1, A2, and A4 one-shot
pulse determines each phase output signal.
No dead time can be set when the INV15 bit is set to 1 (dead time disabled). The INV06 bit in the INVC0
register determines start trigger of the DTT register.
b5
b4
b3
page 134 of 376
b2
b1
(1) (2)
b0
b0
If setting value is n , the timer stops when counting
n times a count source selected by the INV12 bit
in the INVC1 register after start trigger occurs.
Positive or negative phase, which changes from
inactive level to active level, shifts when the dead
time timer stops.
Symbol
(b7-b6)
DWBi
DUBi
DVBi
DWi
DUi
DVi
Bit
-
IDB0, IDB1
Symbol
DTT
Symbol
U-phase output buffer i
U-phase output buffer i
V-phase output buffer i
V-phase output buffer i
W-phase output buffer i
W-phase output buffer i
Reserved bits
Bit Name
Function
01CAh, 01CBh
Address
01CCh
Address
(1)
14. Three-Phase Motor Control Timer Function
Write output level
0: Active level
1: Inactive level
When read, the value of the three-
phase shift register is read.
Set to 0
Function
Setting Range
After Reset
00111111b
1 to 255
After Reset
Undefined
WO
RW
RW
RW
RW
RW
RW
RW
RW
RO