M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 284

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
Figure 21.5 Setting and Resetting of EW0 Mode
Figure 21.6 Setting and Resetting of EW1 Mode
Apr 14, 2006
NOTES:
Procedure to enter EW0 mode
Transfer the rewrite control program in CPU rewrite
mode to a space other than the flash memory
1.In CPU rewrite mode, set the CM06 bit in the CM0 register and bits CM17 to CM16 in the CM1 register to CPU
2.Set the FMR01 bit to 1 immediately after setting it to 0. Do not generate an interrupts or DMA transfer between
3.Exit CPU rewrite mode after executing the read array command.
4.When CPU rewrite mode is exited while the FMR05 bit is set to 1, the user ROM area can be accessed.
5.When in CPU rewrite mode, bits PM10 and PM13 in the PM1 register are set to 1. The rewrite control program
NOTES:
Jump to the rewrite control program transferred to
a space other than the flash memory.
(In the following steps, use the rewrite control
program in a space other than the flash memory.)
clock frequency of 10 MHz or less. Set the PM17 bit in the PM1 register to 1 (with wait state).
setting the bit to 0 and setting it to 1.
Set the bit to 0 if setting to 0. Set this bit in a space other than the flash memory while the NMI pin is held "H".
can only be executed in the internal RAM or in an external area that is enabled for use when the PM13 bit = 1.
Single-chip mode, memory expansion mode
1.In EW1 mode, do not enter the memory expansion mode or boot mode.
2.In CPU rewrite mode, set the CM06 bit in the CM0 register and bits CM17 to CM16 in the CM1 register to
3.Set the FMR01 bit to 1 immediately after setting it to 0. Do not generate an interrupt or a DMA transfer between
CPU clock frequency of 10 MHz or less. Set the PM17 bit in the PM1 register to 1 (with wait state).
setting the bit to 0 and setting it to 1.
Set the FMR11 bit to 1 immediately after setting it to 0 while the FMR01 bit is set to 1.
Do not generate an interrupt or a DMA transfer between setting the FMR11 bit to 0 and setting it to 1.
Set bits FMR01 and FMR11 while "H" is applied to the NMI pin.
Set registers CM0, CM1, and PM1
page 260 of 376
or boot mode
Set the FMR01 bit to 1 (CPU rewrite mode
enabled) after writing 0
Set the FMR11 bit to 1 (EW1 mode) after
writing 0 (EW1 mode)
Set registers CM0, CM1, and PM1
Procedure to enter EW1 mode
Execute the software commands
(1)
(CPU rewrite mode disabled)
Set the FMR01 bit to 0
(5)
Program in the ROM
Single-chip mode
(3)
Rewrite control program
In boot mode only
set the FMR05 bit to 1 (user ROM area access)
Jump to a given address in the flash memory
(1)
Set the FMR01 bit to 1 (CPU rewrite mode
enabled) after writing 0
In boot mode only
Set the FMR05 bit to 0 (Boot ROM area
accessed)
Execute the read array command
Execute the software commands
(CPU rewrite mode disabled)
(2)
Set the FMR01 bit to 0
(4)
(2)
21. Flash Memory Version
(3)