M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 376

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
23.8 Timers
23.8.1 Timer A
23.8.1.1 Timer A (Timer Mode)
23.8.1.2 Timer A (Event Counter Mode)
The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i =
0 to 4) register and the TAi register before setting the TAiS bit in the TABSR register to 1 (count starts).
Always make sure the TAiMR register is modified while the TAiS bit remains 0 (count stops) regardless
whether after reset or not.
While counting is in progress, the counter value can be read out at any time by reading the TAi register.
However, if the counter is read at the same time it is reloaded, the value FFFFh is read. Also, if the
counter is read before it starts counting after a value is set in the TAi register while not counting, the set
value is read.
If a low-level signal is applied to the NMI pin when the IVPCR1 bit in the TB2SC register = 1 (three-phase
output forcible cutoff by input on NMI pin enabled), pins TA1OUT, TA2OUT, and TA4OUT go to a
high-impedance state.
The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR
(i = 0 to 4) register, the TAi register, the UDF register, bits TAZIE, TA0TGL, and TA0TGH in the ONSF
register, and the TRGSR register before setting the TAiS bit in the TABSR register to 1 (count starts).
Always make sure the TAiMR register, the UDF register, bits TAZIE, TA0TGL, and TA0TGH, and the
TRGSR register are modified while the TAiS bit remains 0 (count stops) regardless whether after reset or
not.
While counting is in progress, the counter value can be read out at any time by reading the TAi register.
However, FFFFh can be read in underflow, while reloading, and 0000h in overflow. When setting the TAi
register to a value during a counter stop, the setting value can be read before a counter starts counting.
Also, if the counter is read before it starts counting after a value is set in the TAi register while not
counting, the set value is read.
If a low-level signal is applied to the NMI pin when the IVPCR1 bit in the TB2SC register = 1 (three-phase
output forcible cutoff by input on NMI pin enabled), pins TA1OUT, TA2OUT, and TA4OUT go to a
high-impedance state.
Apr 14, 2006
page 352 of 376
______
______
______
______
23. Usage Notes