LPC2460FET208,551 NXP Semiconductors, LPC2460FET208,551 Datasheet - Page 461

• Manufacturer Part Number: LPC2460FET208,551
• Description: IC ARM7 MCU ROMLESS 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2460FET208,551

• Program Memory Type: ROMless
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/SPI/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB2460, MCB2460U
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4260; 935283232551; LPC2460FET208-S

NXP Semiconductors
UM10237_4
User manual
Fig 70. Auto-baud a) mode 0 and b) mode 1 waveform
a. Mode 0 (start bit and LSB are used for auto-baud)
b. Mode 1 (only start bit is used for auto-baud)
16xbaud_rate
16xbaud_rate
U0ACR start
U1ACR start
rate counter
rate counter
UARTn RX
UARTn RX
4.17 UART1 Fractional Divider Register (U1FDR - 0xE001 0028)
The UART1 Fractional Divider Register (U1FDR) controls the clock pre-scaler for the
baud rate generation and can be read and written at the user’s discretion. This pre-scaler
takes the APB clock and generates an output clock according to the specified fractional
requirements.
Important: If the fractional divider is active (DIVADDVAL > 0) and DLM = 0, the value of
the DLL register must be 3 or greater.
start
start
16 cycles
16 cycles
bit0
bit0
bit1
bit1
start bit
start bit
Rev. 04 — 26 August 2009
bit2
bit2
'A' (0x41) or 'a' (0x61)
'A' (0x41) or 'a' (0x61)
bit3
bit3
bit4
bit4
16 cycles
bit5
bit5
bit6
bit6
LSB of 'A' or 'a'
LSB of 'A' or 'a'
bit7
bit7
Chapter 17: LPC24XX UART1
parity stop
parity stop
UM10237
© NXP B.V. 2009. All rights reserved.
461 of 792