LPC2460FET208,551 NXP Semiconductors, LPC2460FET208,551 Datasheet - Page 552

• Manufacturer Part Number: LPC2460FET208,551
• Description: IC ARM7 MCU ROMLESS 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2460FET208,551

• Program Memory Type: ROMless
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/SPI/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB2460, MCB2460U
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4260; 935283232551; LPC2460FET208-S

NXP Semiconductors
5. Functional overview
UM10237_4
User manual
5.1 Mutimedia card
5.2 Secure digital memory card
There is one additional signal needed in the interface, a power control line MCIPWR, but it
can be sourced from any GPIO signal.
The MCI may be used as a multimedia card bus host (see
card”) or a secure digital memory card bus host (see
memory
digital memory card may be connected.
Figure 21–104
Multimedia cards are grouped into three types according to their function:
The multimedia card system transfers commands and data using three signal lines:
Figure 21–105
Fig 104. Multimedia card system
•
•
•
•
•
•
Read Only Memory (ROM) cards, containing pre-programmed data
Read/Write (R/W) cards, used for mass storage
Input/Output (I/O) cards, used for communication
CLK: One bit is transferred on both command and data lines with each clock cycle.
The clock frequency varies between 0 MHz and 20 MHz (for a multimedia card) or
0 MHz and 25 MHz (for a secure digital memory card).
CMD: Bidirectional command channel that initializes a card and transfers commands.
CMD has two operational modes:
– Open-drain for initialization
– Push-pull for command transfer
DAT: Bidirectional data channel, operating in push-pull mode
card”). Up to 4 multimedia cards (depending on board loading) or a single secure
shows the multimedia card system.
shows the secure digital memory card connection.
Rev. 04 — 26 August 2009
MULTIMEDIA CARD STACK
CARD
POWER
SUPPLY
MULTIMEDIA CARD BUS
Chapter 21: LPC24XX SD/MMC card interface
CARD
MULTIMEDIA
INTERFACE
CARD
Section 21–5.2 “Secure digital
CARD
Section 21–5.1 “Mutimedia
UM10237
© NXP B.V. 2009. All rights reserved.
552 of 792