UPD70F3765GF-GAT-AX Renesas Electronics America, UPD70F3765GF-GAT-AX Datasheet - Page 1055

• Manufacturer Part Number: UPD70F3765GF-GAT-AX
• Description: MCU 32BIT V850ES/JX3-H 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Hr

Specifications of UPD70F3765GF-GAT-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: CSI, EBI/EMI, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JG3-H, V850ES/JH3-H
R01UH0042EJ0400 Rev.4.00
Sep 30, 2010
(e) GET_STATUS() request
(f) SET_ADDRESS() request
A STALL response is made in the data stage if any of wValue, wIndex, or wLength is other than the values
shown in Table 21-3. A STALL response is also made in the data stage if the target is an interface or an
endpoint that does not exist.
• Default state:
• Addressed state: The value stored in the target status register
• Configured state: The value stored in the target status register
A STALL response is made in the status stage if either of wIndex or wLength is other than the values shown in
Table 21-3. A STALL response is also made if the specified device address is greater than 127.
• Default state:
• Addressed state: The device enters the Default state and returns the USB Address value to be input to SIE
• Configured state: The device remains in the Configured state and returns the USB Address value to be input
Note The target status register is as follows.
• If the target is a device: UF0 device status register L (UF0DSTL)
• If the target is endpoint 0: UF0 EP0 status register L (UF0E0SL)
• If the target is endpoint n: UF0 EPn status register L (UF0EnSL) (n = 1 to 4, 7)
The value stored in the target status register
request has been received and when the request is for a device or Endpoint0; otherwise a
STALL response is made in the data stage.
request has been received and when the request is for a device or Endpoint0; otherwise a
STALL response is made in the data stage.
request has been received and when the request is for a device or an endpoint that exists;
otherwise a STALL response is made in the data stage.
The device enters the Addressed state and changes the USB Address value to be input to
SIE into a specified address value if the specified address is other than 0 when the
SET_ADDRESS() request has been received. If the specified address is 0, the device
remains in the Default state.
to the default address if the specified address is 0 when the SET_ADDRESS() request
has been received. If the specified address is other than 0, the device remains in the
Addressed state, and changes the USB Address value to be input to SIE into a specified
new address value.
to SIE to the default address if the specified address is 0 when the SET_ADDRESS()
request has been received. In this case, the endpoints other than endpoint 0 remain valid,
and control transfer (IN), control transfer (OUT), bulk transfer and interrupt transfer for an
endpoint other than endpoint 0 are also acknowledged. If the specified address is other
than 0, the device remains in the Configured state and changes the USB Address value to
be input to SIE into a specified new address value.
CHAPTER 21 USB FUNCTION CONTROLLER (USBF)
Note
Note
Note
is returned only when the GET_STATUS()
is returned only when the GET_STATUS()
is returned only when the GET_STATUS()
Page 1055 of 1509