MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 311

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

the input source to the SPLL (main system oscillator or EXTCLK). MODCK1, MODCK2, and MODCK3
together determine the multiplication factor at reset and the functionality of limp mode.
If the configuration of PITRTCLK and TMBCLK and the SPLL multiplication factor is to remain
unchanged in power-down low-power mode, the MODCK signals should not be sampled at wake-up from
this mode. In this case the PORESET pin should remain negated and HRESET should be asserted during
the power supply wake-up stage.
When MODCK1 is cleared, the output of the main oscillator is selected as the input to the SPLL. When
MODCK1 is asserted, the external clock input (EXTCLK pin) is selected as the input to the SPLL. In all
cases, the system clock frequency (freq
that freq
The TBS bit in the SCCR selects the time base clock to be either the SPLL input clock or GCLK2. When
the backup clock is functioning as the system clock, the backup clock is automatically selected as the time
base clock source.
The PITRTCLK frequency and source are specified by the RTDIV and RTSEL bits in the SCCR. When
the backup clock is functioning as the system clock, the backup clock is automatically selected as the time
base clock source.
When the PORESET pin is negated (driven to a high value), the MODCK1, MODCK2, and MODCK3
values are not affected. They remain the same as they were defined during the most recent power-on reset.
Table 8-1
Freescale Semiconductor
MODCK[1:3]
gclk2(max)
000
001
010
011
shows the clock configuration modes during power-on reset (PORESET asserted).
The MODCK[1:3] are shared functions with IRQ[5:7]. If IRQ[5:7] are used
as interrupts, the interrupt source should be removed during PORESET to
insure the MODCK pins are in the correct state on the rising edge of
PORESET.
1
occurs when the DFNH bits are cleared.
LME
0
0
1
1
RTSEL
0
0
0
0
Table 8-1. Reset Clocks Source Configuration
Default Values after PORESET
MPC561/MPC563 Reference Manual, Rev. 1.2
RTDIV
0
1
1
1
gclk2
) can be reduced by the DFNH[0:2] bits in the SCCR. Note
MF + 1
1
1
5
1
NOTE
Division
PITCLK
256
256
256
4
TMBCLK
Division
16
16
4
4
Used for testing purposes.
Normal operation, PLL enabled.
Main timing reference is crystal
osc (20 MHz).
Limp mode disabled.
Normal operation, PLL enabled.
Main timing reference is crystal
osc (4 MHz).
Limp mode enabled.
Normal operation, PLL enabled.
Main timing reference is crystal
osc (20 MHz).
Limp mode enabled.
SPLL Options
Clocks and Power Control
8-9