MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 331

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

8.11
8.11.1
The SPLL has a 32-bit control register, SCCR, which is powered by keep-alive power.
Freescale Semiconductor
VFLASH (5 V)
1
2
3
4
5
VDDA, VRH
IRAMSTBY
VDD, NVVL,
QVDDL
VDDH ≥ QVDDL - 0.5 V
VDDA can lag VDDH, and VDDSYN can lag QVDDL, but both must be at a valid level before resets are negated.
If keep-alive functions are NOT used, then when system power is on: KAPWR = QVDDL ± 0.1 V; KAPWR ≤ 2.7 V
If keep-alive functions ARE used, then KAPWR = QVDDL = NVDDL = 2.6 V ± 0.1 V when system power is on
KAPWR = 2.6 V ± 0.1 V when system power is off. IRAMSTBY should be powered prior to the other supplies. If
IRAMSTBY is powered at the same time as the other supplies, it should be allowed to stabilize before PORESET
is negated. Normal system power is defined as QVDDL = VDD = VDDF = VDDSYN = KAPWR = 2.6 ± 0.1 V and
VDDA = VDDH = VFLASH = 5.0 ± 0.25 V. Flash programming requirements are the same as normal system
power. VFLASH should always be 5.0 ± 0.25 V. Note: Flash is not implemented on the MPC561.
Do not hold the 2.6-V supplies at ground while VDDH/VDDA is ramping to 5 V.
If 5 V is applied before the 2.6-V supply, all 5-V outputs will be in indeterminate states until the 2.6-V supply
reaches a level that allows reset to be distributed throughout the device If 5 V is applied before the 2.6-V supply,
all 5-V outputs will be in indeterminate states until the 2.6-V supply reaches a level that allows reset to be
distributed throughout the device
PORESET
VDDSYN
HRESET
KAPWR
Clocks Unit Programming Model
VDDH
System Clock Control Register (SCCR)
For more detailed information on power sequencing see
“Power-Up/Down
No Battery Connect Battery
Figure 8-15. Standby and KAPWR, Other Power-On/Off
MPC561/MPC563 Reference Manual, Rev. 1.2
Sequencing.”
NOTE
Power On
Operating
Section F.8,
Power Off
Clocks and Power Control
No Battery
8-29