MCF51EM128CLL Freescale Semiconductor, MCF51EM128CLL Datasheet - Page 284

• Manufacturer Part Number: MCF51EM128CLL
• Description: IC MCU 32BIT 128KB FLASH 100LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF51EMr

Specifications of MCF51EM128CLL

• Core Processor: Coldfire V1
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LCD, LVD, PWM, WDT
• Number Of I /o: 63
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: MCF51EM
• Core: ColdFire V1
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: RS-232, LIN
• Maximum Clock Frequency: 50 MHz
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: TWR-MCF51CN-KIT, TWR-SER, TWR-ELEV, TOWER
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8-bit Serial Peripheral Interface (SPI)
pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT
waveform applies to the slave select output from a master (provided MODFEN and SSOE = 1). The master
SS output goes to active low one-half SPSCK cycle before the start of the transfer and goes back high at
the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a
slave.
When CPHA = 1, the slave begins to drive its MISO output when SS goes to active low, but the data is not
defined until the first SPSCK edge. The first SPSCK edge shifts the first bit of data from the shifter onto
the MOSI output of the master and the MISO output of the slave. The next SPSCK edge causes both the
master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the
third SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled,
and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the
master and slave, respectively. When CHPA = 1, the slave’s SS input is not required to go to its inactive
high level between transfers.
Figure 12-10
shown for reference with bit 1 starting as the slave is selected (SS IN goes low), and bit 8 ends at the last
SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting
12-12
(MISO OR MOSI)
(MASTER OUT)
(REFERENCE)
(SLAVE OUT)
SAMPLE IN
MSB FIRST
BIT TIME #
(CPOL = 0)
(CPOL = 1)
LSB FIRST
(MASTER)
(SLAVE)
SS OUT
SPSCK
SPSCK
SS IN
MOSI
MISO
shows the clock formats when CPHA = 0. At the top of the figure, the eight bit times are
MCF51EM256 Series ColdFire Integrated Microcontroller Reference Manual, Rev. 8
Figure 12-9. SPI Clock Formats (CPHA = 1)
BIT 7
BIT 0
1
BIT 6
BIT 1
2
...
...
...
BIT 2
BIT 5
6
BIT 1
BIT 6
7
Freescale Semiconductor
BIT 0
BIT 7
8