MPCBL0050N02Q Intel, MPCBL0050N02Q Datasheet - Page 199

• Manufacturer Part Number: MPCBL0050N02Q
• Manufacturer: Intel

Specifications of MPCBL0050N02Q

• Lead Free Status / RoHS Status: Supplier Unconfirmed

Firmware Update Utilities—MPCBL0050
Table 76.
September 2007
Order Number: 318146-001
-o
-t
none
none
none
none
none
none
none
Short Option
Name
Long Option Name
--output
--target
--no-capture-rb
--force-id
--force-fw-update
--force-fpga-update
--force-fru-update
--force-sdr-update
--no-reset
Common command line options and arguments (Sheet 2 of 2)
<file>
KCS interface
0x20 | rtm | 0x20:rtm
LAN interface
0xNN[:rtm] | bladeN[:rtm]
none
none
none
none
none
none
none
Possible Argument
Use with –M get to save the contents of the FRU or the
SDR to a file. The name of the file is specified as the
argument to -o.
The file extension given at the end of the file name
determines whether FRU or SDR data is saved and
whether the data is stored in ASCII or binary form as
follows:
<file>.fru – Save FRU data in ASCII
<file>.bfru – Save FRU data in binary
<file>.sdr – Save SDR data in ASCII
<file>.bsdr – Save SDR data in binary
KCS interface
LAN interface
Applies only to staged firmware updates. This option does
not capture a rollback image, thus preserving the contents
of the rollback area.
Forces the firmware update to occur. This is needed to
override product ID or manufacturer ID mismatches.
(This happens if the SBC is in fail safe mode.)
This option is needed to downgrade the firmware version
or if the target is in firmware update mode and version
information is not available. This forces the firmware
update in these cases.
Sbcupdate will automatically request this option if the
version of FPGA currently running on the SBC is different
from the version included in the new IPMC FW image that
is being updated. Otherwise, this option will not be
required.
This option is needed to downgrade the FRU version, if the
FRU version information is missing from the system or
from the input file, or also performing a full FRU update.
The option forces the FRU update in these cases.
This option is needed to downgrade the SDR version, if
SDR information is missing either from the system or from
the input file, or if the target has a pending staged
firmware update. This option forces the SDR update in
these cases.
Applies only to staged firmware updates. This option stops
a reset of the target IPMC from being performed after
performing a staged firmware update. This should not
affect payload operation.
• 0x20 denotes the local SBC and targets the local
• rtm or 0x20:rtm denotes the RTM on the local SBC.
• Omitting the –t option is equivalent to specifying –t
• The value of NN in 0xNN is the hexadecimal IPMB
• The value of N in bladeN can range from 1–14,
• The IPMB to physical slot mapping used in the Intel
• If :rtm is appended to either target, the RTM on the
• Note that upgrade of the FPGA automatically initiates
Intel NetStructure
IPMC.
0x20.
address of the SBC. The IPMC on that SBC is targeted.
inclusive determining which SBC to use in the chassis.
NetStructure
Table 79, “Mapping of physical slot to IPMB address in
Intel NetStructure
page
specified SBC is targeted.
payload hard reset.
232. The IPMC on the specified SBC is targeted.
®
MPCHC0001 chassis is assumed. See
®
®
Description
MPCBL0050 Single Board Computer
MPCHC0001 14U Shelf” on
Technical Product Specification
199