F39-EU1E Omron, F39-EU1E Datasheet - Page 267

• Manufacturer Part Number: F39-EU1E
• Description: F3S-B OPTIONAL PROGRAMMING KIT
• Manufacturer: Omron

Specifications of F39-EU1E

• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Light Curtain Type: Safety
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: [phone]-Outside Local Area: [phone]-www.stevenengineering.com
Safety Precautions
Fig. 1
• This product is a switch for teaching the machine such as robot in
• Apply load current not to exceed the rated value.
• Do not use the switch submerged in oil or water or in locations
• Do not use the switch in locations where explosive or flammable
• Mount the switch securely to prevent it from falling. Otherwise,
• The durability of the switch is greatly influenced by the switching
• Always attach the cover after completing wiring and before using
• The user must not maintain or repair equipment incorporating the
• Do not disassemble or remodel the switch in any case, or the
• Do not override by inserting the Holding Key itself in the door
• Configure the circuit so that the machine does not operate when
• Do not impose excessive vibration or shock on the Door Switch
• Do not incline and pull the switch body or do not impose shock on
• Refer to the D4NS Safety-door Switch Datasheet and Instruction
No operation
Always verify the operation of the safety functions before
starting the system. Not doing so may result in the safety
functions not performing as expected if the wiring or
settings are incorrect or the switches have failed.
Do not drop the switch. Doing so may damage the switch
and the system may continue to operate, possibly
causing injury or death.
hazardous area. The machine is allowed to operate only when
operating the switch continuously. Configure the system so that the
machine can be operated only at position 2.
continuously subject to splashes of oil or water. Doing so may
result in oil or water entering the switch.
gasses may be present.
injuries may occur.
conditions. Always test the switch under actual conditions before
application and use it in a switching circuit for which there are no
problems with performance.
the switch. Electric shock may occur if the switch is used without
the cover attached.
switch. Contact the manufacturer of the equipment for any
maintenance or repairs required.
switch will not operate normally.
switch.
operating the Enabling Switch while the Holding Key is being
inserted in the door switch.
while the Holding Key is inserted. Excessive vibration or shock
may cause the Switch to fail or break.
the switch body in the directions shown with the arrows in Fig.1.
Otherwise, the switch may be damaged and may not operate
properly.
Sheet about the storage, ambient conditions, the details and
handling of the Switch.
Precautions for Safe Use
http://www.ia.omron.com/
Insertion-pull direction
(Perpendicular direction)
No operation
Holding Key
A4EG-OP3
(sold separately)
!WARNING
No operation
D4NS (sold separately)
A4EG
No operation
Mounting surface
Arrow indicates
insertion-pull direction.
Top position
Magnified View
Operating Environment
Mounting Method
Specified Tightening Torque
Loose screws may result in malfunction. Tighten the screws at the
specified torques.
Cover Mounting
Installing Mounting Bracket
• Do not hold the Enabling Switch Device at Position 2 by any other
• This switch is designed for use indoors. Using the switch outdoors
• The switch contacts can be used with either standard loads or
• Do not use the switch in the following locations.
• Do not use the switch where corrosive gasses (e.g.,H
• Do not store the switch where corrosive gasses (e.g.,H
• If the switch is not turned ON and OFF for a long period of time,
• Dislocation of the seal rubber or foreign substance on the seal
• Do not touch the rubber boot with sharp objects. Otherwise, the
• Securely install the Mounting Bracket using M5 screws and
Cover mounting screw
Terminal screw
Holding Key mounting screw
Conduit Connector mounting
(Conforming spanner 27 mm
(width across flats))
Mounting Bracket
methods except for handling. Otherwise, the original function of the
Enabling Switch Device is not worked.
may damage it.
microloads. Once the contact be used to switch smaller loads. The
contact surfaces will become rough once they have been used and
contact reliability for smaller loads may be reduced.
NH
temperature and humidity. Doing so may result in damage to the
switch as a result of contact failure or corrosion.
NH
humidity.
contact resistance may be increased or continuity failure may
occur due to contact oxidation.
rubber reduces seal performance of the switch. Mount the cover
after confirming that there is no abnormality on the seal rubber. If
the seal rubber cracks or breaks, replace the Cover with a new one
(A4EG-OP1 Rubber Cover, separately sold).
rubber boot may break and the operating characteristics and the
seal performance may not be satisfied.
washers and tighten them to a torque of 2.4 to 2.8 N·m.
• Locations where the interior of the Protective Door may into
• Locations subject to detergents, thinners, or other solvents
• Locations subject to sudden temperature changes
• Locations subject to high humidity and condensation
• Locations subject to severe vibration
direct contact with cutting chips, metal filings, oil chemicals
3
3
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
,HNO
,HNO
3
3
, or Cl
, or Cl
Precautions for Correct Use
Item
2
2
) are present or in locations subject to high
) or dust are present or in high temperature and
Rubber boot
Seal Cover, A4EG-OP1 (sold separately)
Seal rubber
Specified torque
1.1 to 1.3 N·m
0.4 to 0.5 N·m
0.5 to 0.7 N·m
2.0 to 2.4 N·m
2.4 to 2.8 N·m
2
S, SO
2
A4EG
S, SO
2
,
2
,
11