F39-EU1E Omron, F39-EU1E Datasheet - Page 863

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

Using the Safety Light Curtain to initiate a machine cycle after an

object is removed from the sensing area is called Presence Sensing

Device Initiation (PSDI). Use of PSDI places additional requirements

on the guarding and safety controls. It can restrict advanced Safety

Light Curtain features such as floating blanking and fixed blanking.

Details on PSDI can be found in ANSI RIA 15.06-1999, OSHA

1910.217(h), and ANSI B11.2-1995 (R2005).

For wiring

For PNP output, connect the load between the output and 0 V

line. Connecting the load between the output and +24 V line

results in a dangerous condition because the operation mode is

reversed to “ON when light is interrupted.”

Do not interconnect an output line with a +24-V line. Otherwise,

the output is always ON, creating a dangerous situation. Also, 0

V of the power supply must be grounded so that output does not

turn ON due to grounding of the output line.

Configure the system by using the optimal number of control

outputs that satisfy the requirements of the necessary safety

category.

Do not connect the lines of the MS/MSF4800 to a DC power

supply higher than 24 V +20%. Also, do not connect to an AC

power supply. Otherwise, it may result in electric shock.

Programming and Diagnostics Module

The MS/MSF4800-series Safety Light Curtains require the use of a

Programming and Diagnostics Module (PDM) to program the

operating parameters of the Light Curtain. In addition to Safety Light

Curtain configuration, this Module also serves as a diagnostics

device, allowing the user to retrieve fault information.

Note: The light curtain does not require the PDM to operate. The

• Displays programming and diagnostics information on a multi-line

• Supports English and Japanese languages. To switch between

• The housing is rated IP65, allowing permanent mounting near the

Up/Down Scroll Buttons

Sensor Restart of Machine Cycle Operation (PSDI)

LCD display.

English and Japanese, continue to press the right Forward/

Backward Scroll Button more than ten times at the log-in screen

that appears after the PDM is connected to the MS/MSF4800.

Safety Light Curtain.

Forward/Backward

factory default settings allow for basic guarding operation.

Scroll Buttons

http://www.ia.omron.com/

WARNING

In the interest of product improvement, specifications are subject to change without notice.

Enter Button

For the MS/MSF4800 to comply with IEC 61496-1 and UL 508, the

DC power supply unit must satisfy all of the following

conditions:

Double or enhanced insulation from hazardous voltage must be

applied to all input and output lines. Failure to do so may result

in electric shock.

The cable extension length must be no greater than the specified

length. Otherwise, the safety functions may fail to work properly,

resulting in danger.

PDM Navigation Buttons

Note: For information on the operating method, refer to the Mini Safe

• Must be within rated power voltage (24 VDC ±20%).

• Must have tolerance against the total rated current of devices

• Must comply with EMC directives (industrial environment).

• Double or enhanced insulation must be applied between the

• Automatic recovery must be possible for overcurrent

• Output holding time must be 20 ms or longer.

• Must satisfy output characteristic requirements for class 2

• Must comply with the EMC, laws, and regulations of the

Forward/

Backward

Scroll But-

tons

Up/Down

Scroll But-

tons

Enter But-

ton

if it is connected to multiple devices.

primary and secondary circuits.

protection.

circuit or limited voltage current circuit defined by UL508.

country or region where the MS/MSF4800 is used. (For

example, in the EU, the power supply must comply with the

EMC Low Voltage Directive.)

Name

4800 Series Safety Light Curtains Installation and Operating

Manual.

Shape

Scroll forward and backward to

review the previous and next

menu, or to move within the

same screen.

Scroll up and down to review the

selection of the current menu.

When pressed the selected func-

tion will be accessed.

Description

MS4800

F39-EU1E Omron, F39-EU1E Datasheet - Page 863

F39-EU1E

Specifications of F39-EU1E

Related parts for F39-EU1E