F39-EU1E Omron, F39-EU1E Datasheet - Page 287

• Manufacturer Part Number: F39-EU1E
• Description: F3S-B OPTIONAL PROGRAMMING KIT
• Manufacturer: Omron

Specifications of F39-EU1E

• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Light Curtain Type: Safety
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: [phone]-Outside Local Area: [phone]-www.stevenengineering.com
Wiring
Operating Environment
LEDs
Using the Microload
Naked Crimp Terminals
Crimp Terminals with
Insulating Sheaths
When DC-specific LEDs are used, wire the Switch so that the X1
terminal is positive.
Terminal screws must be Phillips or slotted M3.5 screws with a
square washer.
The tightening torque is 1.08 to 1.27 N·m.
Single wires, stranded wires, and crimp terminals can be
connected to the Switch.
Applicable Wiring Materials:
Twisted strands: 2 mm
Solid wire: 1.6 mm dia. max.
After wiring the Switch, maintain an appropriate clearance and
creepage distance.
The IP65 model is designed with a protective structure so that it will
not sustain damage if it is subjected to water from any direction to
the front of the panel.
The Switch is intended for indoor use only. Using the Switch
outdoor may cause it to fail.
The LED current-limiting resistor is built-in, so internal resistance is
not required.
If commercially available LEDs are used, select the ones that meet
the following conditions:
Base: BA9S/13
Overall length: 26 mm max.
Power consumption: 2.6 W max.
Contact failure may occur if a Switch designed for a standard load
is used to switch a microload. Use Switches within the application
ranges shown in the following graph. Even within the application
range, insert a contact protection circuit, if necessary, to prevent
the reduction of life expectancy due to extreme wear on the
contacts caused by loads where inrush current occurs when the
contact is opened and closed.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (
The equation,
malfunction rate is less than 1/2,000,000 with a reliability level of
60%.
30
12
24
60
0
5
60
0.1
) (conforming to JIS C5003).
http://www.ia.omron.com/
0.16 mA
Invalid
area
= 0.5 x 10
2
1 mA
max.
1
1.6 mA
Microload area
20.2 mm max.
16.0 mm max.
6
/time indicates that the estimated
10 mA
10
8 mm max.
8 mm max.
Current (mA)
100 mA
100
20.2 mm max.
Standard
load area
16.0 mm max.
Area of
use
1,000
8 mm dia. max.
8 mm dia. max.
Others
If the panel is to be coated, make sure that the panel meets the
specified dimensions after coating.
Due to the structure of the Switch, severe shock or vibration may
cause malfunctions or damage to the Switch.
Also, most Switches are made from resin and will be damaged if
they come into contact with sharp objects. Particularly scratches
on the Operation Unit may create visual and operational
obtrusions.
Handle the Switches with care, and do not throw or drop them.
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
Hammer
Screwdriver
Do not operate the
Switch with hard or
sharp objects.
Do not place or drop
heavy objects on the
Switch.
Do not allow the
Switch to drop and hit
the floor.
A22E
17