F39-EU1E Omron, F39-EU1E Datasheet - Page 673

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

Mutual interference

prevention function

Series connection

Test functions

Safety functions

Connection type

Protective circuits

Ambient temperature

Ambient humidity

Ambient operating light

intensity

Insulation resistance

Dielectric strength

Degree of protection

Vibration resistance

Shock resistance

Connection cable, Series

connection cable (F39-JJR@L,

F39-JJR3W)

Extension cable (F39-JC@A,

F39-JC@B)

Materials

Weight (packed state)

Accessories

Applicable standards

Model

http://www.ia.omron.com/

Interference light prevention algorithm

Time division emission by series connection

Connectors (M12, 8-pin)

Output short-circuit protection, and power supply reverse polarity protection

Operating: −10 to 55°C (no icing), Storage: −30 to 70°C

Operating: 35% to 85% (no condensation), Storage: 35% to 95%

Incandescent lamp: 3,000 lx max. (light intensity on the receiver surface), Sunlight: 10,000 lx max. (light intensity on the receiver

surface)

20 MΩ min. (at 500 VDC)

1,000 VAC 50/60 Hz, 1 min

IP65 (IEC60529)

Malfunction: 10 to 55 Hz, 0.7-mm double amplitude, 20 sweeps in X, Y, and Z directions

Malfunction: 100 m/s

6-mm-dia., 8-wire cable (0.15 mm

6.6-mm-dia., 8-wire cable (0.3 mm

Casing (including metal parts on both ends): Aluminum, zinc die-cast

Cap: ABS resin

Optical cover: PMMA resin (acrylic)

Cable: Oil resistant PVC

Calculate using the following equations:

For F3SJ-A@@@@P@@-TS, weight (g)=(protective height) × 1.5 + α

The values for α are as follows:

Protected height 245 to 590 mm: α = 1,100

Protected height 600 to 1,130 mm: α = 1,500 protected height 2,195 to 2,500 mm: α = 2,600

Protected height 1,140 to 1,655 mm: α = 2,000

Test rod, instruction manual, mounting brackets (top and bottom), mounting brackets (intermediate) (*), error mode label, User's

Manual (CD-ROM)

* Number of intermediate mounting brackets depends on protective height of F3SJ.

IEC61496-1, EN61496-1 UL61496-1, Type 4 ESPE (Electro-Sensitive Protective Equipment)

IEC61496-2, prEN61496-2, UL61496-2, Type 4 AOPD (Active Opto-electronic Protective Devices)

IEC61508, EN61508 SIL3

(To extend a cable length, use an equivalent or higher-performance cable. Do not place it in the same duct as high-voltage cables

or power cables.)

For available length for extension (cable extension length), see page 21.

• Number of connections: up to 3 sets

• Total number of beams: up to 240 beams

• Maximum cable length for 2 sets: no longer than 15 m

• Response time under connection: See page 20

• Self test (when power is turned ON and while power is supplied)

• External test (emission stop function by test input)

• External device monitor

• Muting (Override function included. F39-CN6 Key Cap for muting is required.)

• When more than 3 Units are connected in series.

• When the total number of beams connected in series exceeds 240.

• When any model other than a "-TS" model is included in a series connection.

• For protective height from 600 to 1,130 mm: 1 set for each of the emitter and receiver is included

• For protective height from 1,140 to 1,655 mm: 2 sets for each of the emitter and receiver are included

• For protective height from 1,660 to 2,180 mm: 3 sets for each of the emitter and receiver are included

•

Lockout occurs under either of the following conditions:

For protective height from 2,195 to 2,500 mm: 4 sets for each of the emitter and receiver are i

F3SJ-A@@@@P20-TS

, 1,000 times each in X, Y, and Z directions

× 8) with braided shield, allowable bending radius R5 mm

× 4P, resistance 0.058 Ω/m), allowable bending radius R36 mm

protected height 1,660 to 2,180 mm: α = 2,400

F3SJ-A@@@@P25-TS

ncluded

F3SJ Ver.2

F39-EU1E Omron, F39-EU1E Datasheet - Page 673

F39-EU1E

Specifications of F39-EU1E

Related parts for F39-EU1E