EP4SE530H40I3 Altera, EP4SE530H40I3 Datasheet - Page 329

• Manufacturer Part Number: EP4SE530H40I3
• Description: IC STRATIX IV FPGA 530K 1517HBGA
• Manufacturer: Altera
• Series: STRATIX® IV Er

Specifications of EP4SE530H40I3

• Number Of Logic Elements/cells: 531200
• Number Of Labs/clbs: 21248
• Total Ram Bits: 27376
• Number Of I /o: 976
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 1517-HBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -

© 2011 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
SIV51009-3.2
Stratix IV Hot-Socketing Specifications
Stratix IV Device Handbook Volume 1
February 2011
February 2011
SIV51009-3.2
This chapter describes hot-socketing specifications, power-on reset (POR)
requirements, and their implementation in Stratix
Stratix IV devices offer hot socketing, also known as hot plug-in or hot swap, and
power sequencing support without the use of external devices. You can insert or
remove a Stratix IV device or a board in a system during system operation without
causing undesirable effects to the running system bus or board that is inserted into the
system.
The hot-socketing feature also removes some of the difficulty when you use Stratix IV
devices on PCBs that contain a mixture of 3.0-, 2.5-, 1.8-, 1.5-, and 1.2-V devices.
The Stratix IV hot-socketing feature provides:
■
■
■
This section also describes POR circuitry in Stratix IV devices. POR circuitry keeps the
devices in the reset state until the power supply outputs are within operating range
(provided V
This chapter contains the following sections:
■
■
■
■
Stratix IV devices are hot-socketing compliant without the need for external
components or special design requirements. Hot-socketing support in Stratix IV
devices has the following advantages:
■
■
■
Board or device insertion and removal without external components or board
manipulation
Support for any power-up sequence with the exception that V
fully before V
I/O buffers non-intrusive to system buses during hot insertion
“Stratix IV Hot-Socketing Specifications”
“Hot-Socketing Feature Implementation in Stratix IV Devices” on page 9–2
“Power-On Reset Circuitry” on page 9–3
“Power-On Reset Specifications” on page 9–4
“Stratix IV Devices can be Driven Before Power Up” on page 9–2
“I/O Pins Remain Tri-Stated During Power Up” on page 9–2
“Insertion or Removal of a Stratix IV Device from a Powered-Up System” on
page 9–2
CC
powers up fully before V
CCAUX
9. Hot Socketing and Power-On Reset in
for all Stratix IV production devices
CCAUX
).
®
IV devices.
Stratix IV Devices
CC
must power up
Subscribe